JVC HR-XVC24S manual For Example

Page 59

 

 

 

 

 

EN 59

 

 

 

 

* The default setting is bold in the table below.

 

 

 

 

 

8 PICTURE CONTROL

 

This feature helps you to adjust the playback picture quality according to your

NORM

 

preference. Normally select “NORM.”

EDIT

 

NORM:

Picture quality is adjusted automatically.

SOFT

 

EDIT:

Minimizes picture degradation during editing (recording and playback).

SHARP

 

 

SOFT:

Reduces image coarseness when viewing overplayed tapes containing a

 

 

 

 

 

lot of noise.

 

 

 

 

SHARP

Clearer, sharper-edged picture when viewing images with lots of flat,

 

 

 

same-colored surfaces such as cartoons.

 

 

NOTES:

 

 

 

 

 

● When you select “EDIT,” “SOFT” or “SHARP,” the selected mode will not change until you

 

 

select another mode.

 

 

 

 

● When you select “EDIT” to dub tapes, be sure to select “NORM” after you finish dubbing

 

 

the tapes.

 

 

 

 

 

 

 

 

8 SUPERIMPOSE

 

When this function is set to “ON,” various operational indicators appear on the TV

ON

 

screen. Messages appear in the selected language. ( pg. 18)

OFF

 

NOTES:

 

 

 

 

 

 

 

 

 

 

● When you use this unit as the source player for editing, be sure to set “SUPERIMPOSE” to

 

 

“OFF” before starting.

 

 

 

 

● During playback, the operation mode indicators may be disturbed depending on the type of

 

 

tape being used.

 

 

 

 

 

 

 

 

8 AUTO SP]EP TIMER

 

When this function is set to “ON,” the unit automatically switches to EP mode to

ON

 

allow complete recording if there is not enough tape to record the entire program

OFF

 

while timer-recording in SP mode.

 

 

For Example:

 

 

 

 

 

Recording a program of 140 minutes in length onto a 120-minute tape

 

 

Approximately 110 minutes

Approximately 30 minutes

 

 

 

 

 

 

 

SP mode

EP mode

 

 

 

 

 

 

 

 

 

 

Total 140

minutes

 

 

 

Make sure you set this function to “ON,” before the timer-recording starts.

 

 

NOTES:

 

 

 

 

 

● If you have programed the unit to timer-record 2 or more programs, the second program

 

 

and those thereafter may not fit on the tape if you set “AUTO SP]EP TIMER” to “ON.” In

 

 

this case, make sure the mode is not engaged, then set the tape speed manually during

 

 

timer programing.

 

 

 

 

● In order to ensure that the recording fits on the tape, this feature may leave a slight non-

 

 

recorded section at the end of the tape.

 

 

● There may be some noise and sound disturbance at the point on the tape where the unit

 

 

switches from SP to EP mode.

 

 

 

 

● The Auto SP]EP Timer feature is not available during ITR (Instant Timer Recording), and

 

 

the feature will not work properly on the following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and

 

 

T(ST)-120.

 

 

 

 

 

 

 

 

 

Page 58 Page 60
Image 59
Page 58 Page 60
Contents For Customer Use HR-XVC24SDeclaration of Conformity Dear CustomerGrounding or Polarization Power SourcesPower Cord Protection Power LinesBefore YOU Install Your NEW Unit On placing the unit Do not place the unitDo not block the unit’s ventilation openings or holes To mobile phone usersAbout Discs DVD deck only Scan Mode Set DVD deck onlyRemote Control Functions Mode Set VCR deck Mode Set DVD deck Child LockRegion Number About DiscsPlayable Discs Unplayable DiscsCare and Handling of Discs File Structure of DiscsPlacing a Disc J K L M N O P Front ViewFront Display Panel 10 ENRear View On the tape Shows you where you are BeginningOn-Screen Display VCR deck To recall an indicationOne Touch Replay Button  pg , 42 m Skip Search Button  pg How To Use12 EN RemoteConnect the unit to TV Check the contentsConnect the unit to power source Situate the unitSet the VCR channel to off 8To connect to a TV with component video input connectors14 EN DVD deck onlySelect the DVD deck Scan Mode SetSwitch the mode Turn on the unit16 EN Perform Plug & Play setupWhat to do if Plug & Play setting failed Plug & Play SetDVD deck Select the modeSelect the mode setting Monitor Set18 EN LanguageLANGUAGE, then press Access the DVD Set Up menu screenHightlight to on Screen 20 EN On the DVD Set Up menu screen as an exampleProcedure shows how to set Menu Language See Language Code List  pgLanguage Code List Preparations Access the Clock Set screenClock Set 22 ENManual Clock Set Semiauto Clock SetAuto Channel Set Access the Tuner Set screenTuner Set 24 ENTo add channels Access the Manual Channel Set screenManual Channel Set Add or skip the desired channels26 EN Basic PlaybackActivate frame-by-frame playback Slow MotionVariable Speed Search Pause during playbackInstant ReView 28 ENSkip Search Index SearchActivate Repeat Playback Next Function MemoryRepeat Playback One Touch ReplaySoundtrack Selection Adjust the tracking manually30 EN Manual TrackingPause/Resume recording Choose a programSet the tape speed Start recordingRecord One Program While Watching Another Instant Timer Recording ITREngage the ITR mode 32 ENSet the counter display Reset the counterTape Remaining Time Second Audio RecordingEnter the program stop time Access the Program screen34 EN Enter the program start timeCable Box or DBS Receiver Users Engage the unit’s timer modeTo Timer-Record Weekly Or Daily Serials Enter the channel positionPress PROG. Check again Disengage the timer mode36 EN Press PROG. CheckPress Timer To cancel or change a programCancel or change a program Return to the timer modeSelect the program to modify Cancel or change program setting38 EN Confirm the overlapping programsSatellite Auto Recording You can also connect the cable box if it has a timerPress 8 Stop 40 ENLoad the disc Pause playbackLocating the Start Point of the Item or Skip the Item Locating a desired scene using the DVD menuAccess the DVD menu Access the PBC menuActivate frame-by-frame playback 42 ENZooming Select menu item Access the repeat modeSelect the repeat mode Access the on-screen barSubtitle Selection 44 ENTime Search Svcd Select the audio settingAngle Selection Select the view angleSound Effect VFP function Adjusting the picture quality46 EN Select menu item How to Access the On-Screen BarAccess the status bar Access the menu barMenu Bar Functions for SVCD/Video CD/Audio CD 48 ENOutline Control display PrecautionsPlay 50 ENBasic Playback Select the groupZooming a still picture Group/File Selection52 EN Edit From a CamcorderStart the source player Set the input mode of recording deckEngage the Record Pause mode of the recording deck Another Video RecorderFrom DVD to VCR Dubbing54 EN For the digital audio device Digital Audio DubbingPlace a disc and load a MD Prepare the audio device for dubbing56 EN Make connections VCR deck Mode SetAccess the Function Set screen 58 ENFor Example 60 EN When this function is set to onPress rt to select ON, then press Enter For each mode setting, see corresponding pagesLanguage Picture Audio Others Back to the beginning Press rt to move the hightlight to RESUME, then press Enter62 EN Picture SettingsAudio Settings You dub audio of a DVD Video disc recorded with surround Select this when you enjoy multichannel surround audio byConnecting the unit’s analog Audio Output connector Surround multichannel audioSet the Child Lock Others SettingsChild Lock 64 ENOn the Remote On the unitLights up on the front display panel DVD indicator lights up on the frontPress DVD so that the DVD indicator 66 ENRecording cannot be started There is no cassette loaded, or Timer recording won’t workIncorrectly  and $ on the front display 68 ENCheck the programed data and re AgainTo lock the disc tray VHS indicator disappears fromTray Lock Select a different host channel duringPlayback 70 ENSignal system Signal-to-noise ratio 45 dBHorizontal resolution Input/Output RCA connectors X 1, OUT x72 EN Still Picture/Frame-By-Frame Playback Scan Mode Set DVD deck onlyWhen programs overlap each other Zooming74 EN Page HR-XVC24S
Top Page Image Contents