JVC HR-XVC24S Tray Lock, VHS indicator disappears from, Select a different host channel during

Page 69

			EN 69
OTHER PROBLEMS

	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	The image of TV broadcast appears	● The unit leaves turned on and the DVD	Turn off the unit, or press VCR to select
	distorted on the TV screen.	deck is selected.	the VCR deck, then press TV/VCR so that
			the VHS indicator disappears from the
			front display panel.

2.	Whistling or howling is heard from the	● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

3.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them. ( pg. 25)

4.	The channel cannot be changed.	● Recording is in progress.	Press 9 PAUSE to pause the recording,
			change channels, then press 4 PLAY to
			resume recording.

5.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

6.	Even though Auto or Semiauto Clock	● The clock setting data received from the	Select a different host channel during
	Set has been performed, the clock is	host channel is incorrect.	“Semiauto Clock Set” ( pg. 23), or
	incorrect.		perform “Manual Clock Set” ( pg. 23).

ATTENTION

This unit contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the unit off and unplug the AC power cord. Then plug it in again and turn the unit on. Take out the cassette. After checking the cassette, operate the unit as usual.

Tray Lock

You can lock the disc tray to prohibit the unwanted disc ejection by children.

To lock the disc tray.

While the unit is turned off, press and hold 8 STOP, then press x OPEN/CLOSE on the unit. “LOCK” appears on the front display panel and the disc tray is locked.

To unlock tray

While the unit is turned off, press and hold 8 STOP, then press x OPEN/CLOSE on the unit. “UNLOCK” appears on the display panel.

Image 69

Contents For Customer Use HR-XVC24SDeclaration of Conformity Dear CustomerPower Cord Protection Power SourcesPower Lines Grounding or PolarizationBefore YOU Install Your NEW Unit Do not block the unit’s ventilation openings or holes Do not place the unitTo mobile phone users On placing the unitRemote Control Functions DVD deck only Scan Mode Set DVD deck onlyMode Set VCR deck Mode Set DVD deck Child Lock About DiscsPlayable Discs About DiscsUnplayable Discs Region NumberFile Structure of Discs Placing a DiscCare and Handling of Discs J K L M N O P Front View10 EN Rear ViewFront Display Panel On-Screen Display VCR deck Shows you where you are BeginningTo recall an indication On the tape12 EN How To UseRemote One Touch Replay Button pg , 42 m Skip Search Button pgConnect the unit to power source Check the contentsSituate the unit Connect the unit to TV14 EN 8To connect to a TV with component video input connectorsDVD deck only Set the VCR channel to offSwitch the mode Scan Mode SetTurn on the unit Select the DVD deckWhat to do if Plug & Play setting failed Perform Plug & Play setupPlug & Play Set 16 ENSelect the mode setting Select the modeMonitor Set DVD deck18 EN LanguageAccess the DVD Set Up menu screen Hightlight to on ScreenLANGUAGE, then press Procedure shows how to set Menu Language On the DVD Set Up menu screen as an exampleSee Language Code List pg 20 ENLanguage Code List Clock Set Access the Clock Set screen22 EN PreparationsManual Clock Set Semiauto Clock SetTuner Set Access the Tuner Set screen24 EN Auto Channel SetManual Channel Set Access the Manual Channel Set screenAdd or skip the desired channels To add channels26 EN Basic PlaybackVariable Speed Search Slow MotionPause during playback Activate frame-by-frame playbackSkip Search 28 ENIndex Search Instant ReViewRepeat Playback Next Function MemoryOne Touch Replay Activate Repeat Playback30 EN Adjust the tracking manuallyManual Tracking Soundtrack SelectionSet the tape speed Choose a programStart recording Pause/Resume recordingEngage the ITR mode Instant Timer Recording ITR32 EN Record One Program While Watching AnotherTape Remaining Time Reset the counterSecond Audio Recording Set the counter display34 EN Access the Program screenEnter the program start time Enter the program stop timeTo Timer-Record Weekly Or Daily Serials Engage the unit’s timer modeEnter the channel position Cable Box or DBS Receiver Users36 EN Disengage the timer modePress PROG. Check Press PROG. Check againCancel or change a program To cancel or change a programReturn to the timer mode Press Timer38 EN Cancel or change program settingConfirm the overlapping programs Select the program to modifySatellite Auto Recording You can also connect the cable box if it has a timerLoad the disc 40 ENPause playback Press 8 StopAccess the DVD menu Locating a desired scene using the DVD menuAccess the PBC menu Locating the Start Point of the Item or Skip the Item42 EN ZoomingActivate frame-by-frame playback Select the repeat mode Access the repeat modeAccess the on-screen bar Select menu item44 EN Time SearchSubtitle Selection Angle Selection Select the audio settingSelect the view angle SvcdVFP function Adjusting the picture quality 46 ENSound Effect Access the status bar How to Access the On-Screen BarAccess the menu bar Select menu itemMenu Bar Functions for SVCD/Video CD/Audio CD 48 ENOutline Control display PrecautionsBasic Playback 50 ENSelect the group PlayZooming a still picture Group/File Selection52 EN Edit From a CamcorderEngage the Record Pause mode of the recording deck Set the input mode of recording deckAnother Video Recorder Start the source playerDubbing 54 ENFrom DVD to VCR Place a disc and load a MD Digital Audio DubbingPrepare the audio device for dubbing For the digital audio device56 EN Make connections Access the Function Set screen Mode Set58 EN VCR deckFor Example 60 EN When this function is set to onLanguage Picture Audio Others Back to the beginning For each mode setting, see corresponding pagesPress rt to move the hightlight to RESUME, then press Enter Press rt to select ON, then press EnterPicture Settings Audio Settings62 EN Connecting the unit’s analog Audio Output connector Select this when you enjoy multichannel surround audio bySurround multichannel audio You dub audio of a DVD Video disc recorded with surroundChild Lock Others Settings64 EN Set the Child LockOn the Remote On the unitPress DVD so that the DVD indicator DVD indicator lights up on the front66 EN Lights up on the front display panelRecording cannot be started There is no cassette loaded, or Timer recording won’t workCheck the programed data and re 68 ENAgain Incorrectly and $ on the front displayTray Lock VHS indicator disappears fromSelect a different host channel during To lock the disc trayPlayback 70 ENHorizontal resolution Signal-to-noise ratio 45 dBInput/Output RCA connectors X 1, OUT x Signal system72 EN When programs overlap each other Scan Mode Set DVD deck onlyZooming Still Picture/Frame-By-Frame Playback74 EN Page HR-XVC24S