Grizzly G0706 owner manual Safety Instructions for Machinery

Page 8

SECTION 1: SAFETY

For Your Own Safety, Read Instruction Manual Before Operating this Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

 

 

 

Indicates an imminently hazardous situation which, if not avoided,

 

 

 

WILL result in death or serious injury.

 

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

 

 

COULD result in death or serious injury.

 

 

 

 

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

 

 

MAY result in minor or moderate injury. It may also be used to alert

 

 

 

 

 

 

against unsafe practices.

 

NOTICE

This symbol is used to alert the user to useful information about

 

proper operation of the machine.

Safety Instructions for Machinery

1.READ ENTIRE MANUAL BEFORE STARTING. DeZgVi^c\ bVX]^cZ WZ[dgZ gZVY^c\ i]Z bVcjVa \gZVian ^cXgZVhZh i]Z g^h`d[^c_jgn#

2.ALWAYS USE ANSI APPROVED SAFETY GLASSES WHEN OPERATING MACHINERY. :kZgnYVn ZnZ\aVhhZh dcan ]VkZ ^beVXi gZh^hiVci aZchZh i]Zn VgZ CDIhV[Zin\aVhhZh#

3.ALWAYS WEAR A NIOSH APPROVED RESPIRATOR WHEN OPERATING MACHINERY THAT PRODUCES DUST. BdhiineZhd[YjhilddY!bZiVa!ZiX#XVc XVjhZhZkZgZgZhe^gVidgn^aacZhhZh#

4.ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. BVX]^cZgn cd^hZ XVc XVjhZ eZgbVcZci ]ZVg^c\adhh#

5.WEAR PROPER APPAREL. 9D CDI lZVgaddhZXadi]^c\!\adkZh!cZX`i^Zh!g^c\h! dg _ZlZagn i]Vi XVc XViX] ^c bdk^c\ eVgih# LZVg egdiZXi^kZ ]V^g XdkZg^c\ id XdciV^c adc\]V^gVcYlZVgcdc"ha^e[ddilZVg#

6.NEVER OPERATE MACHINERY WHEN TIRED OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. 7ZbZciVaanVaZgi ViVaai^bZhl]Zcgjcc^c\bVX]^cZgn#

"+"

BdYZa<%,%+B[\#h^cXZ&&$%.

Image 8
Contents Model G0706 Parallelogram Jointer Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Manual AccuracyContact Info Machine DescriptionIdentification Machine Data Sheet Fence Information Safety Safety Instructions for MachineryKeep CHILDREN/VISITORS Away Additional Safety for Jointers 220V Single-Phase Operation Circuit RequirementsSetup Items Needed for SetupUnpacking Description QtyHardware and Tools Figure Qty Crate Contents QtyInventory Hardware Recognition Chart Cleanup H9692-Orange Power Cleaner & DegreaserVcYZVhangZbdkc\gjhiegZkZciVikZ#  Eji dc hVZin \aVhhZh VcY YhedhVWaZ \adkZh#Site Considerations Moving & Placing Base Unit Mounting to Shop FloorBolting to Concrete Floors To lift the jointerAssembly To assemble the jointer@cdW =ZmCjiTo test run the machine Dust Port Test RunTo connect a dust collection hose  HiVgihiZbVXcZ# OperationsOperation Overview Basic Controls Follow these rules when choosing and joint- ing stock Stock Inspection Requirements#/22%#4 ™ Only process natural wood fiber throughSquaring Stock Surface Planing To surface plane the workpiece on the joint- erEdge Jointing To edge joint on the jointerCZZYiVWaZ# Bevel CuttingTo bevel cut on the jointer Rabbet Cutting To rabbet cut on the jointer HZiiZXjiic\YZeidgndjgdeZgVidc#LZ Xjiic\#Cutterhead Inserts Tools Needed QtyTo rotate or replace a spiral cutterhead insert  EdhidciZhigV\iZY\ZdciZdjiZZYiVWaZH9291-12 Shelix Spiral Cutterhead AccessoriesXjiiZgZVYh# G1029Z2-2HP Dust Collector G9643-8 Precision StraightedgeMaintenance CleaningSchedule LubricationHnbeidb EdhhWaZ8VjhZ EdhhWaZHdajidc ServiceTroubleshooting DjiZZYiVWaZhhZiidd\# Checking Outfeed Table Height Setting Outfeed Table HeightOutfeed Table Height To set the outfeed table height Checking/Adjusting Table Parallelism Checking Outfeed Table ParallelismDjiZZYIVWaZ XjiiZgZVYWdYn#To check the infeed table Adjusting Table ParallelismChecking Infeed Table Adjusting Outfeed Table Parallelism Adjusting Infeed Table Parallelism GZVg AZi6YjhibZci GdciSetting Infeed Table Stop Bolt To adjust the infeed table stop boltsSetting Fence Stops Calibrating Depth ScaleTo calibrate the depth scale To set the 45˚ inward fence stopTo set the 90˚ fence stop  I\iZciZVbcji# BdYZa%,%+B\#hcXZ&&$%.To set the 45 outward fence stop Hide7dai ?Vb CjiAdjusting Belt Tension To adjust the belt tensionDrive Belt Checking Belt TensionPulley Alignment Replacing BeltWiring Wiring Safety InstructionsG0706 Electrical Components HIDEHliX HI6GIHliXG0706 Wiring Diagram Magnetic Switch AssemblyParts FenceBdYZa%,%+B\#hcXZ&&$%. Table Parts List Cutterhead Stand Assembly Stand Parts List Labels & Cosmetic BdYZa%,%+B\#hcXZ&&$%. 10. 8dbbZcih EaVXZ HiVbe =ZgZ $5342!, .# 0/ /8  %,,.!- 7! 22!.49 !.$ 2%452.3 Order Hours a DAY