GoVideo DV1140 user manual Connections, Connecting Antenna/Cable TV to, Preparation

Page 11

Connections

Tips

Depending on your TV and other equipment you wish to connect, there are various ways you could connect the DVD+VCR. Use connections described on pages 11-13. Please refer to the manuals of your TV, VCR, Stereo System or other devices as necessary to make the best connections.

For better sound reproduction, connect the DVD+VCR’s DVD/VCR AUDIO OUT jacks to the audio in jacks of your amplifier, receiver, stereo or audio/video equipment. See Optional, Preferred TV Connections on pages 12-13.

Caution

Make sure the DVD+VCR is connected directly to the TV. Tune the TV to the correct video input channel.

Do not connect the DVD+VCR’s DVD/VCR AUDIO OUT jacks to the phono in jack (record deck) of your audio system.

Do not connect your DVD+VCR via your VCR. The DVD image could be distorted by the copy protection system.

Connecting Antenna/Cable TV to

DVD+VCR

1 TV.Disconnect the antenna leads from the rear of the

2a round cable as illustrated, it is a 75 ohm coaxial

antenna cable. This cable will connect directly to the jack marked ANT.IN on your DVD+VCR.Identify the type of cable from your antenna. If it is

Tip

If your antenna lead wire is a flat type antenna cable, connect it to an Antenna Adaptor (300-ohm to 75-ohm) (not supplied) and slip the Adaptor onto the ANT.IN jack. The Adaptor does not screw on to the DVD+VCR, it just slips over the jack.

Without Cable Box

If your cable wire is connected to your TV without a converter or descrambler box, unscrew the wire from your TV and attach it to the ANT.IN jack on the DVD+VCR. Use the supplied round coaxial cable to connect between the DVD+VCR’s RF.OUT jack and the 75 ohm antenna input jack on the TV. With this connection, you can receive all midband, super band, and hyperband channels.

With Cable Box

If a converter is required in your cable system, follow the instructions below:

The cable hookup permits both TV and DVD+VCR operation.

To view or record CATV channels

1Tune the TV to the DVD+VCR output channel (CH 3 or 4).

2Set the DVD+VCR channel selector to the output channel of the Cable Converter box by pressing the CH (v/V) or num- ber (0-9) buttons on your DVD+VCR. (Example: CH3)

3Select the channel to view on the Cable Converter Box.

otes

zWith this connection, you CANNOT record one program while viewing another.

zIf you are using a cable box to tune channels, it is not nec- essary to do Auto Channel Programming as indicated on page 15.

Cable TV

Wall Jack

Back Panel of

Typical Cable Box

Rear of DVD+VCR

PREPARATION

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents DVD+VCR Regulatory Information FCC Part Safety PrecautionsOtes on Copyrights Introduction Important Safety InstructionsTable of Contents Playable Discs Remote control battery installationRemote Control Operation Range Before UseSetting the Output Source PrecautionsAbout Symbols Front Panel REC Display WindowDVD Remote Control ANT.IN Antenna Input Rear PanelVideo OUT DVD OUT Digital Audio OUT Coaxial DVD OUTPreparation Connecting Antenna/Cable TV toConnections Optional, Preferred TV Connections Connections Basic TV ConnectionsA1A2 Accessory Audio/Video A/V Connections toDigital Multi-channel sound Rear of DVD+VCR OteMenu Selection VCR Operation Setup On-Screen Display OSDSetting the On-Screen Display Channel Selection VCR Operation Setup Setting the VCR Setup MenuManual Clock Set VCR Operation Setup Setting the ClockAuto Clock Set On-screen display operation DVD Operation SetupGeneral Explanation On-Screen DisplayDisplay DVD Operation Setup Initial SettingsInitial Settings General Operation LanguageOthers AudioLock Operation Operation with tape Normal PlaybackSpecial Effect Playbacks To record one TV program while watching another Timer RecordingOperation with tape Normal Recording To pause the recordingSame day, priority is given to Earliest recording. For Checking Erasing the Timer ProgramOperation with tape Program PriorityDubbing and Editing Instant Timer RecordingChecking the Recording Time To extend the Recording TimeTV screen Multichannel TV Sound Indicator MTSMTS Multi-Channel TV Sound SAP Second Audio Program RecordingAdditional Information VCR Operation with tape Tape Counter Memory FeatureOperation with DVD Playing DVD General FeaturesOperation with DVD General Features Additional Information DVD Operation with DVDTo stop playback at any other time Press Stop About MP3About WMA Windows Media Audio Repeat A-B CD Operation with Audio CD and MP3/WMA DiscsMoving to another Track CD MP3 Repeat Track/All/Off CD MP3 WMAInsert a disc and close the tray Operation with Photo Disc Viewing a Photo Disc JpegMoving to Another File To Rotate pictureErasing the Complete Program List Programmed Playback CD MP3Repeat Programmed Tracks Erasing a Track from Program ListSymptom Cause Correction TroubleshootingMoisture Condensation DVD+VCR is in Timer modeReference Video head clogging Troubleshooting Video Head CleaningVideo head cleaning Language Code Language Code ListCountry Code Country Code ListGeneral SpecificationsVCR Specifications DVD SpecificationsR R a N T Y Limited Warranty
Top Page Image Contents