LG Electronics 26LC7D owner manual FCC Notice

Page 3

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and

maintenance (servicing) instructions in the litera- ture accompanying the appliance.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

WARNING / CAUTION

WARNING / CAUTION

To prevent fire or shock hazards, do not expose this product to rain or moisture.

FCC NOTICE

Class B digital device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE TO CABLE/TV INSTALLER

 

 

 

CAUTION

 

 

 

 

 

 

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product

1

Page 2 Page 4
Image 3
Page 2 Page 4
Contents LCD TV Page FCC Notice Important Safety Instructions Safety InstructionsGrounding Use only with the cart, stand, tripod, bracketOutdoor use marking Exposed to dripping or splashing and noContents External Control Through RS-232C Time SettingIntroduction Feature of this TVAccessories PreparationPreparation Here shown may be somewhat different from your TV Remote Control SensorFront Panel Information Front Panel Controls 26 inchesFront Panel Controls 32/42 inches Back Connection Panel Back Panel InformationVideo ServiceComponent AV OUTHow to remove the Cable Management Back Cover for Wire ArrangementEnsure the eye-bolts or brackets are tightened securely Attaching the TV to a WallStand Installation Only 26/32 inches LCD TV models Vesa Wall Mounting Desktop Pedestal InstallationAntenna Analog or Digital Antenna or Cable ConnectionHow to use External Equipment SetupHD Receiver Setup When connecting Component cable 1. How to connectHow to connect When connecting Hdmi cableWhen connecting Hdmi to DVI cable DVD Setup When connecting with an S-Video cable When connecting with an antenna VCR SetupMono jack of the set Select AV1 input source by using the Input button on= white, and Audio Right = red Insert a video tape into the VCR and press Play onOther A/V Source Setup Audio PC Setup720x400 RGB-PC, HDMI1/DVI-PC mode HDMI1/DVI-DTV, HDMI2-DTV modeRGB-PC mode only 640x350 60.00To initialize the adjusted values Screen Setup for PC mode OverviewAdjustment for screen Resolution, Position, Size, and Phase Initializing Reset to original factory valuesAV OUT Setup SetupExternal Equipment Set the TV Speaker option Off in the Audio Digital Audio OutputRemote Control Functions Watching TV / Channel Control Installing BatteriesVolume Adjustment Turning on TVChannel Selection Option ON-SCREEN Menus SelectionWatching TV / Channel Control Lock For CanadaChannel Search Press the Enter button to add or delete the channel Select Manual ScanSelect T V, DTV, CATV, and Cadtv Select channel you want to add or deleteChannel After EZ Scan on the Setup menuThere are two different ways in order to add or delete Small window at the top-left corner of the screenDTV Signal Strength Press the G button and then use D or Button to Input Source SelectionWatching Select the source T V, AV1, AV2, Component1Input Label SimpLink Preparations SimpLink Menu SimpLink Functions169 Picture ControlPicture ControlCropped. The picture taking a halfway trade off ZoomPicture Control Preset Picture SettingsColor Tone Preset Manual Picture Adjustment EZ Picture User ModeSelect EZ Picture Or G button to Color Tone User ModeSelect X D XD Picture Improvement TechnologyAdvanced Cinema 32 Pull Down Mode Advanced Black Darkness Level Select Video Reset Picture ResetSound & Language Control Preset Sound Settings EZ SoundLanguage Control SoundPress the G button and then use F or G button to Make appropriate adjustmentsBalance Select BalanceSound & Language Control TV Speakers ON/OFF SetupPress Exit button to save and return to TV viewing STEREO/SAP Broadcasts SetupStereo, or SAP appear in turn Them with the SAP buttonAudio Language ON-SCREEN Menus Language Selection Text Caption / TextAnalog Broadcasting System Captions CaptionOr French Digital Broadcasting System CaptionsTo select the Option menu Select Caption/TextSize Set the word size Caption OptionCustomize the DTV/CADTV captions that appear on your screen Sound & LanguageTime Setting Clock SettingAuto Clock Setup Time Setting Manual Clock SetupButton and then use Or E button to Auto ON/OFF Timer SettingSleep Timer Setting Select O n or Off Auto SHUT-OFF SettingTo select the Time menu Select Auto OffChip rating and categories SET Password & Lock SystemSetting up Your Password Parental Control / RatingsLock System Set PasswordChannel Blocking External Input BlockingControl / Rating Movie & TV Rating Movie Rating Mpaa for USA onlyRating TV Rating Children for USA only TV Rating General for USA onlyParental Control / Rating TV Rating English for Canada only Appendix TroubleshootingRemote control Doesn’t work Power is suddenly Turned off AppendixVertical bar or stripe on Background AppendixExtended Absence MaintenanceCleaning the Screen Cleaning the Cabinet32LC4D 42LC4D Product SpecificationsProgramming a code into a remote mode Programming the Remote ControlVCR Remote Control CodeDVD Repeat frame Remote Control IR CodesIR Codes 1st frameCode Function GND RS-232C SetupType of Connector D-Sub 9-Pin Male External Control Throuth RS-232CRXD TXD GND DTR DSR RTS CTS RS-232C ConfigurationsCommunication Parameters Either cable below can be usedTransmission / Receiving Protocol Command Reference ListSet ID OK/NGDatax Set ID DataCr Step
Top Page Image Contents