3.1.ADC Process
(1)ADC
-Enter Service Mode by pushing "ADJ" key,
-Enter Internal ADC mode by pushing "►" key at "7. ADC Calibration".
| EZ ADJUST | ADC Calibration | |
0. | Tool Option1 | ADC Comp 480i | NG |
1. | Tool Option2 | ADC Comp 1080p | NG |
2. | Tool Option3 | ADC RGB | NG |
3. | Tool Option4 |
|
|
4. | Tool Option 5 | Start | Reset |
5.Country Group
6.Area Option
7. ADC Calibration
8.White Balance
9.10 Point WB
10.Test Pattern
11.EDID D/L
12.Sub B/C
13.Touch Sensitivity Setting
<Caution> Using
If there is no Component Input, disappear “ADC Comp” message.
* ADC Calibration Protocol (RS232)
NO | Item | CMD 1 | CMD 2 | Data 0 |
| ||
|
|
|
|
|
|
| |
Enter | Adjust | A | A | 0 | 0 | When transfer the ‘Mode In’, | |
Adjust MODE | ‘Mode In’ | Carry the command. | |||||
|
|
|
| ||||
ADC adjust | ADC Adjust | A | D | 1 | 0 | Automatically adjustment | |
(The use of a internal pattern) | |||||||
|
|
|
|
|
| ||
Adjust Sequence
▪aa 00 00 [Enter Adjust Mode]
▪xb 00 40 [Component1 Input (480i)]
▪ad 00 10 [Adjust 480i Comp1]
▪xb 00 60 [RGB Input (1024*768)] (only LD21B)
▪ad 00 10 [Adjust 1024*768 RGB] (only LD21B)
▪aa 00 90 End Adjust mode
* Required equipment : Adjustment remote control.
4. Total Assembly line process
4.1. Adjustment Preparation
▪ W/B Equipment condition CA210
: CCFL/EEFL
▪ Above 5 minutes H/run in the inner pattern. (“power on” key of adjust remote control)
Mode | Temp | Coordinate spec | Target |
| |
Cool | 13,000k | X=0.269 (±0.002) | X=0.271 | <Test Signal> | |
|
| Y=0.273 (±0.002) | Y=0.276 | Inner pattern | |
|
| X=0.285 (±0.002) | X=0.287 | ||
Medium | 9,300k | (204gray, | |||
Y=0.293 (±0.002) | Y=0.296 | ||||
|
| 80IRE) | |||
Warm | 6,500k | X=0.313 (±0.002) | X=0.315 | ||
| |||||
Y=0.329 (±0.002) | Y=0.332 |
| |||
|
|
|
▪ Edge LED W/B Table in process of aging time (Only LGD Edge LED Module except AUO, CMI, IPS Module)
CA210 : CH 14, Test signal : Inner pattern (80IRE)
| Aging |
| Cool | Medium | Warm | |||
GP4 | time | X |
| y | x | y | x | y |
| (Min) | 269 |
| 273 | 285 | 293 | 313 | 329 |
1 | 279 |
| 288 | 295 | 308 | 319 | 338 | |
2 | 278 |
| 286 | 294 | 306 | 318 | 336 | |
3 | 277 |
| 285 | 293 | 305 | 317 | 335 | |
4 | 276 |
| 283 | 292 | 303 | 316 | 333 | |
5 | 274 |
| 280 | 290 | 300 | 314 | 330 | |
6 | 272 |
| 277 | 288 | 297 | 312 | 327 | |
7 | 271 |
| 275 | 287 | 295 | 311 | 325 | |
8 | 270 |
| 274 | 286 | 294 | 310 | 324 | |
9 | Over 150 | 269 |
| 273 | 285 | 293 | 309 | 323 |
*Connecting picture of the measuring instrument (On Automatic control)
Inside PATTERN is used when W/B is controlled. Connect to auto controller or push Adjustment R/C POWER ON → Enter the mode of
3.2. Function Check
3.2.1. Check display and sound
■Check Input and Signal items. (cf. work instructions)
1.TV
2.AV
3.COMPONENT (480i)
4.RGB (PC : 1024 x 768 @ 60hz)
5.HDMI
6.PC Audio In
* Display and Sound check is executed by Remote controller
Caution : Not to push the INSTOP KEY after completion if the function inspection.
Full White Pattern | |
|
|
COLOR
ANALYZER
TYPE :
*
(1)Adjust in the place where the influx of light like floodlight around is blocked. (illumination is less than 10 lux).
(2)Adhere closely the Color analyzer(CA210) to the module less than 10 cm distance, keep it with the surface of the Module and Color analyzer's prove vertically.(80° ~ 100°).
(3)Aging time
-After aging start, keep the power on (no suspension of power supply) and
-Using 'no signal' or 'POWER ONLY' or the others, check the back light on.
Copyright © | LG Electronics. Inc. All rights reserved. | - 11 - | LGE Internal Use Only |
Only for training and service purposes |
|
| |