V-COM AdjustOnly LGDM+S Module | LG Electronics 32LT360C-ZA specification

(1) HD RGB EDID data

(2) HD HDMI EDID data

	0		1	2	3	4	5	6		7		8	9	A			B		C	D		E	F
00	00		FF	FF	FF	FF	FF	FF		00		1E	6D			a					b
10		c		01	03	80	A0	5A		78		0A	EE		91			A3	54	4C		99		26
20	0F		50	54	A1	08	00	31		40		45	40		61			40	71	40		01		01
30	01		01	01	01	01	01	66		21		50	B0		51			00	1B	30		40		70
40	36		00	40	84	63	00	00		1E		64	19		00			40	41	00		26		30
50	18		88	03	06	40	84	63		00		00	18		00			00	00	FD		00		3A
60	3E		1E	53	10	00	0A	20		20		20	20		20			20			d
70									d													01		e
80	02		03	22	F1	4E	10	1F		04		93	05		14			03	02	12		20		21
90	22		15	01	26	15	07	50		09		57	07							f
A0	80		1E	01	1D	80	18	71		1C		16	20		58			2C	25	00		A0		5A
B0	00		00	00	9E	01	1D	00		72		51	D0		1E			20	6E	28		55		00
C0	20		C2	31	00	00	1E	8C		0A		D0	8A		20			E0	2D	10		10		3E
D0	96		00	A0	5A	00	00	00		18		02	3A		80			18	71	38		2D		40
E0	58		2C	45	00	A0	5A	00		00		00	1E		00			00	00	00		00		00
F0	00		00	00	00	00	00	00		00		00	00		00			00	00	00		00		e
(3) Detail EDID Options are below
	a. Product ID
MODEL NAME						HEX				EDID Table								DDC Function
HD/FHD Model						0001					01 00							Analog/Digital
	b. Serial No: Controlled on production line.
	c. Month, Year: Controlled on production line:
		ex) Week : '01' -> '01'
				Year : '2012' -> '16' fix
	d. Model Name(Hex):
			cf) TV set’s model name in EDID data is below.
Model name									MODEL NAME(HEX)

LG TV				00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 (LG TV)

e. Checksum: Changeable by total EDID data.

EDID C/S data		HD
EDID C/S data		HDMI	RGB
		HDMI	RGB
	Block 0	A4	A5
Check sum		5B (HDMI1)
(Hex)	Block 1	4B (HDMI2)	-
		3B (HDMI3)

f. Vendor Specific(HDMI)

Input	Model name(HEX)
HDMI1	67030C001000
HDMI2	67030C002000
HDMI3	67030C003000

4.5. V-COM Adjust(Only LGD(M+S) Module)

-Why need Vcom adjustment?

■The Vcom(Common Voltage) is a Reference Voltage of Liquid Crystal Driving. → Liquid Crystal need for Polarity Change with every frame.

Circuit Block

		Data(R,G,B) &				Gamma
		Control signal				Reference Voltage
S			Timing	Data(R,G,B) & Control signal		Gamma Reference
			Timing
		Interface	Controller
			Controller	Control signal		Voltage
Y	Data Input			Control signal		Voltage
Y	Data Input
S					Source Drive IC
S

T				Gate	Column Line	Panel
E	Power Input	Power		Gate	VCOM	Panel
M		Block		Drive	CLC	CST
M					CLC	CST
						Liquid
			VCOM	IC		Crystal
			VCOM		Row Line TFT

VCOM

-Adjust sequence

■Press the PIP key of the ADJ remote controller. (This PIP key is hot key to enter the VCOM adjusting mode)

(Or After enter Service Mode by pushing “ADJ” key, then Enter V-Com Adjust mode by pushing “►” key at “12. V-Com”)

■As pushing the right or the left button on the remote controller, And find the V-COM value Which is no or minimized the Flicker. (If there is no flicker at default value, Press the exit key and finish the VCOM adjustment.)

■Push the OK key to store value. Then the message “Saving OK” is pop.

■Press the exit key to finish VCOM adjustment.

4.6. Outgoing condition Configuration

■When pressing IN-STOP key by SVC remocon, Red LED are blinked alternatively. And then automatically turn off. (Must not AC power OFF during blinking)

4.7. Hi-pot Test

Confirm whether is normal or not when between power board's ac block and GND is impacted on 1.5 kV(dc) or 2.2 kV(dc) for one second

Copyright ©	LG Electronics. Inc. All rights reserved.	- 12 -	LGE Internal Use Only
Only for training and service purposes