Beko 22WLP530HID operating instructions Performing the initial power-on settings, TV controls

Page 11

6Performing the initial power-on settings

6.1-TV controls

6.1.1-Temporary on/off (STAND-BY)

When you press the red STAND-BYbutton located on the upper left hand side of your remote control while your

television is switched on, the sound and the picture will go off. In the

stand-by mode, the power indicator of your television will glow brighter. To switch your television back on, either press any numeric button or PR+/

PR- buttons.

Caution! If you are not going to use your television for a long time, unplug its power cable from the socket.

6.1.2-Channel Selection

You may select whichever program number you would like by pressing

the PR+/PR- buttons located on your television and your remote control. To select the programs that are above 9, you can use the Numerical buttons.

You may enter the number of the program you would like to select using the numerical buttons. For

example, to switch to the program number 12, press respectively the numeric buttons 1 and 2 on your remote control. You can perform the program selection also from the Program Table.

6.1.3-Digital TV, Analog TV and AV Mode Selection

Press the AV button on your remote control. SOURCE menu will be displayed. Select DIGITAL TV, ANALOG TV or desired AV mode from the Source menu with Up/Down movement buttons and

confirm with OK button so that your television will switch to the source you have selected.

6.1.4-Performing the Volume setting

You can adjust the volume of your television by using the VOL+/VOL- buttons on your remote control.

6.1.5-Temporary sound mute (MUTE)

To temporarily mute the sound of your television, press the MUTE button on your remote control. In

that case, MUTE symbol will appear on the screen. When you press the

same button a second time, the sound will be restored. If you press the VOL+ button while in the Mute mode, the sound level is increased and the Mute function is aborted.

6.1.6-Returning to Selected Program (SWAP)

Allows you to switch between the current program you watch and the

last selected program. For example, if you change the channel to Program 11 while you were watching Program 1, press SWAP button to switch back to Program 1. Press SWAP button to switch back to Program 11 again.

PR 01 PR 11 PR 01

6.1.7-Main Menu

Press the MENU button. The Menu including all the setting menus will appear on the screen. Navigate through the Menu titles with the Up/Down movement buttons and press the OK button to select the desired menu.

If you want to exit the menu in any step, just press the EXIT button. Press BACK or MENU buttons to return to the previous Menu while you are in a sub menu.

MAIN MENU

SOUND

PICTURE

PROGRAM TABLE

SETUP

FEATURES

MENU

SELECTEXIT

9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Operating Instructions Table of Contents Important Information Special Features Features of your new televisionTV for the first time Important Safety InstructionsOperate your TV only Service requirementsNever operate your Page Batteries Powering on your TV and the initial use Start Aerial connectionExternal Connections Your new televisionTV Control Panel Digital Mode Only Remote ControlTV controls Performing the initial power-on settingsManual tuning of channels and storing in the memory Turning on the TV and Setting the ChannelsPerforming Digital Tunings Automatic Tuning of Channels and Storing in the MemoryProgram Table First Time InstallationElectronic TV Guide EPG Digital FeaturesRED button when you are in Program Creating favorite channels listUser Interface Options Language SettingsAccess Control TimersPerforming Analog Tunings If the channel you found is not Fine TuningIf you do not know the channel number To name the channels Switching the locations of the stored channelsDeleting a stored channel Skipping a stored channelPicture Menu Settings Settings of Your New TelevisionSound Menu Settings Tint CCE Color&Contrast EnhancementBacklight Picture SmartFeatures Menu Settings Teletext Toptext optional Temporary TV Picture UpdateQuestion Answer Button Reveal FastextExternal Equipment Connections Connecting an external equipment via Scart connectionConnecting an external equipment via AV connection Side view of TV Connecting an external equipment via Hdmi connectionHdcp High Definition HD-READYRear view of TV Transition to the PC modePC Setting PC connectionHelp and tips Failure Possible cause SolutionGeneral technical specifications Technical specifications chartMain UK Transmitter Stations Important notes Guarantee TelevisionWhat is covered? What is not covered?Special Note HOW to Obtain ServiceFQZ.801
Top Page Image Contents