Yamakawa MP-28 manual Case of difficulty, Symptom Cause Remedy, Others

Page 19

Others

In case of difficulty

If operation freezes, the screen goes black or the unit should otherwise not function properly, try turning the power off then back on. Alternatively, try the following methods in the order listed until the unit returns to normal playback mode.

Turn the car’s ignition OFF and back ON again.

This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult a professional mobile video installer.

 

Symptom

Cause

Remedy

 

 

Unit does not

Fuse is blown.

Replace with a fuse of the specified capacity.

 

 

operate.

Monitor’s power is not turn on.

Turn on the monitor’s power

 

 

 

Condensation

Wait a while(about 1 hour) for the condensation

 

 

 

 

to dry.

 

 

Operation is

Remote control unit’s

Replace the remote control unit’s battery with

 

 

unstable.

battery is worn.

new one.

 

 

 

Remote control sensor or

Clean the sensor or transmitter.

 

 

 

transmitter is dirty.

 

 

 

No picture is

Monitor’s mode is not

Switch to the mode you want to see.

 

 

produced.

switched to the mode you

 

 

 

 

want to see.

 

 

 

Playback does

Disc is loaded upside-down.

Check the disc and load it with the labeled side

 

 

not start.

 

facing upward.

 

 

 

Disc is dirty.

Clean the disc.

 

 

 

A disc not able to playback

Check if the disc is able to be played back.

 

 

 

with this unit is loaded.

 

 

 

 

Parental lock is set.

Cancel the parental lock or change the rating

 

 

 

 

level.

 

 

 

 

 

 

 

Picture is

Disc is being fast-forwarded

The picture may be slightly disturbed, but this

 

 

unclear or noisy

or fast-reversed.

is normal.

 

 

 

Vehicle’s battery power is

Check the battery power and wiring.

 

 

 

weak.

The unit may malfunction if the battery power is

 

 

 

 

under 10.8 volts with a load applied.

 

 

 

Monitor’s fluorescent tube is

Replace the monitor’s fluorescent tube.

 

 

 

worn.

 

 

 

 

 

 

Image stops

Disc is scratched.

Replaced with a non-scratched disc.

 

 

sometimes.

 

 

 

 

 

 

No disc

No disc is loaded.

Load a disc.

 

 

 

Disc is dirty.

Clean the disc.

 

 

Not valid

Remote control operation

For some discs or playing modes, certain

 

 

 

is not possible.

operations are not possible. This not a

 

 

 

 

malfunction.

 

 

VIDEO SIGNAL

PAL( or NTSC) disc is loaded.

Change the TV TYPE of the unit(see SET UP).

 

 

SYSTEM IS NOT

 

 

 

 

 

 

CORRECT

 

 

 

No sound

Select the wrong Audio Out

According to the connection, set right Audio out.

16

Image 19
Contents V1.0 Features Table of Contents Safety Precautions Use the correct ampere rating when replacing fuses PrecautionsThis symbol means important instructions Moisture condensation TemperatureMaintenance Installation locationFront panel Identification of controlsButton Button Playing/Pausing Remote ControlPreparing the remote control When using remote controlOperating with the remote control Connections Loading and unloading a disc Turning the power on and off Press button During playback ,Press RPT FindingChapter/track/title Repeat playbackDisplaying the disc status Displaying the disc statusPlaying DVD or VCD Playing CD or MP3Changing the default settingssetup Default settingssetupChanging Display Others Case of difficulty Symptom Cause RemedyOthers Video SpecificationsSpecifications AudioMounting Bracket X Audio/video cable x IR sensor Accessories and HardwarePower supply cable x Smoke plug cable x Mounting Bracket x Hex bolt M5 x