Harman-Kardon DVD 23 owner manual TV Picture Adjustment with Test Screen

Page 20

Test Screen

Test Screen

When you activate the Test Screen via the OSD you can activate a still image to test all settings and the video performance of your TV. With the vertical color bars you can test the following:

proper color intensity setting on your TV,

the proper color of each bar, showing if the proper video standard is turned on: the colors should be (left to right): black, white, yellow, cyan (turquoise), green, magenta (purple), red, blue, black.

proper color transition, seen as sharp separation of the bars, S-Video will be better than Video, RGB best of all.

the performance of the color filter in your TV (with ”Video” signals), bar edges should show no vertical crawling dots. Here S-Video and RGB formats usually give no problems.

With the grey scale and the black/white fields below the color bars the brightness and contrast of your screen can be adjusted optimally, see chapter ”TV Picture Adjustment” below.

Color Bars

Grey Scale

100% Black/White fields

TV Picture Adjustment with Test Screen

These adjustments may be done now, but you can also make them after setup has been finalized.

Brightness adjustment:

1.Turn down the color control on your TV until the color bars are visible in black and white.

2.Adjust the contrast to the lowest level where you still can see all bars within the grey scale in the test picture separately and clearly.

3.Adjust the Brightness so that the bars in the grey scale are all visible. The bar furtherst to the left has to be as black as possible rather than grey but the next aside must clearly be differable. All the bars in the grey scale have to be gradually and evenly changing from black to whiter, going from left to right.

Contrast adjustment:

1.Adjust the contrast on your TV until you see a bright white bar in the right low corner of the screen and a deep dark black bar at the left.

The optimal contrast setting will depend from your preference and the surrounding light in the TV room.

2.If the brightness of the white bar will no more increase while turning up the contrast or when the borders of the white ”harman/kardon” text letters on top will bloom (overlight) into the black areas, what drasticly will decrease the sharpness of the script, then the Contrast has been turned up too much. Reduce the contrast until these effects will disappear and the video still looks realistic.

3.If you are watching TV with a usual surround- ing daylight, adjust the Contrast so that a nor- mal video picture has about the same looking as the surroundings in your room. By that way the eye is relazed when watching the TV pic- ture. This contrast setting may be reduced when the surrounding light is dimmed, usually improving the sharpness of a video a lot thereby.

4.The grey scale in the middle line needs to have the same clear difference between each bar as before the contrast adjustment. If not, go back to the brightness adjustment and repeat step 3 and then the contrast adjustments, making only minor adjustments each time for optimisation.

Color adjustment.

1.When the Brightness and the Contrast are set optimally, turn up the color control to the level of your perference. Adjust to the level where the colors look strong but still natural, not overdone. If the color level is too high, depending from the TV used some of the bars will seem wider or the color intensity will not increase while the control is turned up. Then the color control must be reduced again. At the end you should test the color intensity also with a video, e.g. pictures of natural faces, flowers, fruit and vegetables and other well known natural articles of our life most usefull for an optimal setting of the color intensity.

2.If your TV has a Tint option (with most European TVs this is available or effective only with NTSC signals, not with PAL), use the large white bar below the Greyscale to tweak the warmth of the picture. Every viewer has a difference in preference as how the glow of the picture should be. Some prefer a little colder picture, some a warmer glow. The Tint function on your TV and the white bar can be used to control this. Adjust the Tint to the level where you feel the white color has the tone you prefer.

20TEST SCREEN

Image 20
Contents DVD 23 Digital Versatile Disc Player Table of Contents Backlit, Ergonomically Designed Remote Control IntroductionThank you for choosing Harman Kardon DVD Easy-to-Use On-Screen Navigation SystemTerminology TerminologyDivX TerminologyFeatures Front Panel Controls Main Information Display PlayOpen/Close Press this button to open or close the Disc Tray Front Panel ControlsFront Panel Information Display Front Panel Information DisplayRemote Control Functions B RepeatLight Press to illuminate remote controller Arrow buttons M/ N/K/L Use to move the cursor in the OSDSKIP/STEP Previous Press to go to Ness Half Brightness OFF Full BrightnessRear Panel Connections ¡ Optical Digital Output ∞ S-Video OutputCoaxial Digital Output § Component Video Outputs Rear Panel ConnectionsSetup and Connections Setup and ConnectionsDolby DTS or Digital decoder Component Video Connection Important Notes on Scart and RGB formatRemote Control Battery installationService life of batteries Remote control operation rangeFor your reference Dolby Digital and DTSBasic Play Disc Playback FeaturesPlayback Basics System Setup System DefaultsSet Up Menu System SetupSystem Settings Audio Settings Video Settings Video Adjustment DivX Video On DemandTest Screen TV Picture Adjustment with Test ScreenTest Screen Using the Status Bar Menu Player MenuPlayer Menu Information DisplaysDVD Language Codes DVD Language CodesLanguage Code Technical Specifications Harman Kardon, Incorporated Partnumber 01.00.YS.SM1.314