Harman-Kardon DMC 1000 manual Step Seven General Setup, Step Eight Advanced Setup

Page 24

INITIAL SETUP

Video Noise Reduction: We recommend that you leave this setting at the default “Off”. If video signal noise is observed when using the analog video outputs, turn this setting on to reduce the noise and improve the picture quality.

Step Seven – General Setup

These general system settings should be accessed with caution. See Figure 22. If you are uncertain about the proper setting for any of these options, consult with your dealer or installer, or contact Harman Kardon Customer Service at www.harmankardon.com.

Figure 22 – General Setup Menu

Software Update: When system software updates are released, this setting will be used during the installation process. Do not make any changes here unless instructed to do so.

Date & Time: The first time the DMC 1000 is used, set the local time and date here.

System Information: This setting displays the software version number and the amount of hard-disc space available. It is informational only.

Step Eight – Advanced Setup

The settings shown in Figure 23 should be used with caution. If you have any doubts about whether it is appropriate to change these settings, con- sult with your Harman Kardon dealer or custom installer.

Reset Factory Defaults: This setting is used to return all of the Setup Menu settings to their factory defaults. They will then have to be reconfigured as required for your application. The contents of the Media Library are not affected by this command.

Network: When the DMC 1000 is connected to a network, the network settings are identified here. These settings may be used with other devices when the DMC 1000 is to be used as a media server as part of a home network. This feature also allows you to test the network connection to make certain that Internet access is available. Press the “9” key on the remote twice, to display the Internet Protocol (IP) address on the front panel.

Language Selected: Select the display language for the DMC 1000’s menus here. Choose from the default English, or Spanish, French, German or Italian.

Format USB: This command allows you to reformat a USB device, which completely erases the contents of the drive. Exercise great caution before reformatting a drive.

Now that your DMC 1000 has been installed and configured, it’s easy to enjoy your favorite audio and video programs from a variety of media, including DVDs, CDs, memory cards, USB drives and the DMC 1000’s own Media Library.

Figure 23 – Advanced Setup Menu

Backup: This setting is used to back up the system and Media Library contents to a USB storage device.

Restore: This setting is used to restore a backup copy of the system settings and Media Library contents. The existing contents of the Media Library will be erased. Use this feature only in the unlikely event that the hard-disc drive in your DMC 1000 has been replaced.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents DMC Safety Information Important Safety InstructionsImportant Safety Information Staple Invoice Here Table of Contents Introduction Thank you for choosing Harman KardonDMC 1000 Digital Media Center Features Data and Control PortsOptical Disc Player Recording destinations Media Library from any sourceMedia Compatibility Disc Formats Supported by This PlayerMPEG-2 digital video XD-Picture Card may be used in Card Slot FRONT-PANEL Controls Remote Front-Panel Door CardFRONT-PANEL Controls Message Display Message Display Master Power Switch REAR-PANEL ConnectionsConnection For iPod models with a dock connector Remote Control Functions Open/Close Press to open or close the disc drawer Disc Menu Press to view a DVD’s menuPlay Press to begin playback Light Press to activate the remote’s backlighting system Installation Step One PlacementStep Four Connect Media Sources See FigureStep Eight Plug In AC Power Step Six Connect the Remote IR Input and OutputStep Nine Insert Batteries in Remote Step Seven Network ConnectionInitial Setup Step Two Display the Setup MenuStep Three Media Library Setup Step One Turn On the DMCStep Four DVD Player Setup Preferred Subtitle Language When available on the disc,Step Five Audio Setup Step Six Video SetupLow frequencies Step Seven General Setup Step Eight Advanced SetupUsing the DMC OperationTurning On the DMC Playing DVDs and CDsChapters and Titles Status DisplayRepeat Play Audio Playback From the Media Library Camera AnglesAudio Soundtracks Is displayed SubtitlesPlaylists Displays all playlists you have programmed Media LibraryData Media Play Queue and PlaylistsCover Art Sort Play QueueUsing TheBridgeTM Auxiliary Analog Audio InputsContent Transfer To transfer the CD’s content to the Media LibraryData CDs Auxiliary InputsMedia Library Solid-State MediaMultizone Operation Zones MenuTroubleshooting Guide Password not accepted Incorrect OSD languageLanguage Picture is displayed Copying to VCRGlossary Glossary Appendix Default settings and worksheets AppendixTable A7 Power Modes Table A8 DVD Language Codes Eula END-USER License Agreement EulaGracenote Eula Gracenote and Muze Terms of Use Eula No Warranty Page Page DMC1000 Technical Specifications Memory Cards
Related manuals
Manual 42 pages 20.22 Kb
Top Page Image Contents