Harman-Kardon DMC 1000 manual Step Five Audio Setup, Step Six Video Setup, Low frequencies

Page 23

Film: Choose this option for material that was originally shot on film, even though you are viewing it on video via a DVD.

Video: Choose this option for material that was shot directly to video, such as concerts and sports programming.

Step Five – Audio Setup

Each setting applies to a certain type of audio output, but only for Zone 1. The audio output to Zones 2, 3 and 4 is always full-range, 2-channel analog line level. See Figure 20.

Figure 20 – Audio Setup Menu

Speaker Setup: A dialog box appears, allowing you to program the Speaker Size settings used with the Zone 1 (6-Channel) Analog Audio Outputs. The settings are dependent on the DVD Bass Management setting in the DVD Player Setup menu.

DVD Bass Management Bypass: This is the default system setting, and should be used when the receiver or processor is capable of performing bass management. Configure the speaker settings on the receiver. All main speakers default to the Large (full-range) setting, and the subwoofer is on. These settings may not be changed.

DVD Bass Management On: Use this setting if the receiver is not capable of performing bass management, to ensure that the low frequencies steered to each channel match the frequency-response capabilities of the speakers.

The default settings are Small (only frequencies of 200Hz and higher are passed) for all of the main speakers, and the subwoofer is on.

With the left and right speakers set to Large, the center speaker may be set to Small or None, but not Large. Change the Center and Surround settings to None for stereo mode when listening to 2-channel recordings. The subwoofer will remain on. Use this configuration when you desire the added power of a separate subwoofer for

the low frequencies.

Change the left and right speaker setting to Small when using a speaker system consisting of small satellites and a subwoofer.

The Center and Surround settings will automatically change to Small, and the Subwoofer setting will remain on; neither setting may be changed.

DVD Bass Management Stereo/LtRt: Use this setting to output a 2-channel signal without a separate low-frequency channel for the subwoofer. The front left and right speakers default to the Large (full-range) setting, with the center, surround and subwoofer speakers all disabled. These settings may not be changed.

Select Save when you have finished your adjustments, or Cancel to return to the Audio Setup Menu without making any changes.

INITIAL SETUP

Digital Audio Out Format: This setting applies to the Optical and Coaxial Digital Audio Outputs only. If the receiver or processor is capable of decoding Dolby Digital, DTS or other compressed digital bitstreams, select the Compressed setting to output these bitstreams in their original format. Otherwise, select Uncompressed to output all audio as 2-channel PCM bitstreams.

NOTE: When Uncompressed is selected, change the DVD Bass Management setting in the DVD Player Setup menu to “Stereo.” It is not possible to simultaneously output a 5.1-channel analog signal and a digital PCM (2-channel) signal.

HDMI Audio Out: We recommend leaving this setting at the default Auto, in which the DMC 1000 will communicate with the device connected to the HDMI Output and automatically select a compatible audio output setting based on the other device’s capabilities. The other settings are:

Compressed: Passes the audio bitstream in its original format, such as Dolby Digital or DTS.

Uncompressed: Decodes the audio bitstream into up to 5.1 channels of PCM audio.

Off: Mutes audio via the HDMI Output.

IMPORTANT NOTE: When the HDMI Output is active for audio, the Optical and Coaxial Digital Audio Outputs are muted. If the HDMI Output is being used for video only and the S/P-DIF outputs are required for audio, turn the HDMI Audio Out setting Off.

Step Six – Video Setup

These settings are usually set automatically by the DMC 1000, depending on which video output is in use. See Figure 21.

Figure 21 – Video Setup Menu

Video Output: When both the analog video outputs and the HDMI Output are connected, select the desired video output. Both HDMI and the analog video outputs are not available simultaneously. Example: The HDMI Output is connected to a display in the main listening room and the Composite Video Output is being distributed to a multizone system.

Output Resolution: Select the desired video output resolution. If you select a resolution higher than the display’s capabilities, the screen will go blank or be scrambled. If that happens, press the Video Mode Button on the remote to cycle through the settings until a compatible setting is selected. The video output resolution is indicated on the front panel.

Picture Mode: Select from the Normal, Vivid, Sport and Nature picture settings to optimize viewing of various types of programs. This setting is a matter of taste, and there is no incorrect setting.

23

Image 23
Contents DMC Important Safety Instructions Safety InformationImportant Safety Information Staple Invoice Here Table of Contents DMC 1000 Digital Media Center IntroductionThank you for choosing Harman Kardon Recording destinations Media Library from any source FeaturesData and Control Ports Optical Disc PlayerMPEG-2 digital video Media CompatibilityDisc Formats Supported by This Player XD-Picture Card may be used in Card Slot Remote Front-Panel Door Card FRONT-PANEL ControlsFRONT-PANEL Controls Message Display Message Display Connection Master Power SwitchREAR-PANEL Connections For iPod models with a dock connector Remote Control Functions Play Press to begin playback Open/Close Press to open or close the disc drawerDisc Menu Press to view a DVD’s menu Light Press to activate the remote’s backlighting system See Figure InstallationStep One Placement Step Four Connect Media SourcesStep Seven Network Connection Step Eight Plug In AC PowerStep Six Connect the Remote IR Input and Output Step Nine Insert Batteries in RemoteStep One Turn On the DMC Initial SetupStep Two Display the Setup Menu Step Three Media Library SetupPreferred Subtitle Language When available on the disc, Step Four DVD Player SetupLow frequencies Step Five Audio SetupStep Six Video Setup Step Eight Advanced Setup Step Seven General SetupPlaying DVDs and CDs Using the DMCOperation Turning On the DMCRepeat Play Chapters and TitlesStatus Display Is displayed Subtitles Audio Playback From the Media LibraryCamera Angles Audio SoundtracksMedia Library Playlists Displays all playlists you have programmedPlay Queue Data MediaPlay Queue and Playlists Cover Art SortAuxiliary Analog Audio Inputs Using TheBridgeTMAuxiliary Inputs Content TransferTo transfer the CD’s content to the Media Library Data CDsSolid-State Media Media LibraryZones Menu Multizone OperationTroubleshooting Guide Copying to VCR Password not acceptedIncorrect OSD language Language Picture is displayedGlossary Glossary Appendix Appendix Default settings and worksheetsTable A7 Power Modes Table A8 DVD Language Codes END-USER License Agreement Eula EulaGracenote Eula Gracenote and Muze Terms of Use Eula No Warranty Page Page Memory Cards DMC1000 Technical Specifications
Related manuals
Manual 42 pages 20.22 Kb