Harman-Kardon AVR 500 manual Reassigning Device-Control Selectors, Press the Volume Up button

Page 30

Programming the Remote

1.Press the Input or Remote Selector bcfor the unit you wish to have associ- ated with the volume control and the Mute button fat the same time until the red light illuminates under the Device Selector.

2.Press the Volume Up button 32 .

3.Press either the AVR aor the TV Device Control Selector c, depending on which system’s volume control you wish to have attached for the punch-through mode. Note that the red light under the Device Control Selector will blink twice and then go out to confirm the data entry.

Example: To have the AVR’s volume con- trol activated even though the remote is set to control the TV, first press the TV Device Control Selector bcand the Mute button fat the same time. Next, press the Volume Up button 32 , followed by the AVR Device Control Selector a.

NOTE: Should you wish to return the remote to the original configuration after entering a Volume Punch-Through, you will need to repeat the steps shown above. However, press the same Device Control Selector in steps one and three.

Reassigning Device-Control Selectors

Although each of the seven Input or Remote Selectors bcis normally assigned to the category of product shown on the remote, it is possible to reassign one of these buttons to operate a second device of another type. For example, if you have two VCRs but no satellite receiver, you may program the “SAT” button to operate a second VCR. Before following the nor-

mal programming steps for either Three-Digit entry or Auto Search code entry, you must first reassign the button with the following steps:

1.Press the Input or Remote Selector bcyou wish to reassign and the Mute button fat the same time until the red light illuminates under the Device Control Selector.

2.Press the Input or Remote Selector bc for the function you wish to program into the reassigned button.

3.Enter the three-digit code for the specific model you wish the reassigned button to operate.

4.Press the same Input or Remote Selector bcpressed in Step 1 once again to store the selection.

Example: To use the SAT button to operate a second VCR, first press the SAT Device Control Selector cand the Mute button fat the same time until the red light glows under the SAT button. Press the VCR button, followed by the three-digit code for the specific model you wish to control. Finally, press the SAT button again.

1

2

3

4

 

5

6

7

8

9

10

11

12

 

13

14

 

 

 

15 16 17

18

19

20

 

21 22 23 24

25 26 27 28

29 30 31 32

 

33

 

34

35

36

37

38

39

40

41

42

43

44

45

46

47

 

48

49

50

 

51

 

 

 

AVR 500

 

 

29PROGRAMMING THE REMOTE

Image 30
Contents Page AVR 500 Audio/Video Receiver AVR 500 Audio/Video Receiver Description and Features IntroductionWhile complex digital systems are hard Safety Information Important Safety InformationUnpacking Front Panel Controls Preset Stations Selector * Tuner ModeVolume Control ÷ Delay Digital Input Selector ù Set Button Information Display Remote SensorCh Direct inputs ¤ as the listening source Analog Source Indictor This indicator Night Mode Indicator This indicatorFront Panel Information Display Rear Panel Connections £ AMRear Panel Connections Remote Control Functions Forward/Reverse Transport Buttons z Night Mode ` Multi-RoomAVR Selector OSD Button Press this button to view the on-screen displays Remote Control Functions Audio Equipment Connections Installation and ConnectionsSystem Installation Connect the analog output of a CD player to the CD inputsSystem and Power Connections System Configuration Speaker Selection and PlacementSpeaker Placement Using the On-Screen Display System SetupPlug the Power Cable ¡ into an unswitched AC outlet Speaker ConfigurationOutput Level Adjustment CEN SpeakerDelay Settings To set the delay times, follow these steps Press the Set button iVor in the on-screen display Press the Set button i Display Brightness OperationBasic Operation Semi-OSDSurround-Mode Selection Volume ControlSource Selection Main Information Display V will now read VFD FullSurround Mode Chart Selecting a Digital Source Night ModeDigital Audio Playback Dolby DigitalTuner Operation Preset TuningRecalling Preset Stations PCM Audio PlaybackTape Recording Output-Level Trim AdjustmentMemory Backup Channel Direct InputMultiroom Operation Multiroom SetupInstallation Multiroom OperationProgramming the Remote Programming the RemoteVolume Punch-Through Programmed Device FunctionsMacro Programming Press the Volume Up button Reassigning Device-Control SelectorsFunction List Setup Code Tables TV Manufacturer/Brand059 008 024 030 065 101 143 160038 070 083 143 154004 058 019 047169 101 127 133 143 160Setup Code Tables VCR Manufacturer/Brand Setup Code Number020 031 063 054133 140 034 067Setup Code Tables CD Setup Code Tables DVDSetup Code Tables SAT Setup Code Tables DVD/LDSetup Code Tables Cable Manufacturer/Brand Setup Code Number Remote Control ModelAmplifier is in protection mode Troubleshooting GuideProcessor Reset Display brightness is turned offTechnical Specifications