Harman-Kardon AVR 500 manual To set the delay times, follow these steps, Press the Set button i

Page 20

System Configuration

To set the delay times, follow these steps:

1.Put the AVR 500 in the Dolby Pro Logic mode by pressing the Dolby Pro Logic Selector î on the front panel or by

pressing the Surround Mode Selector 31 on the remote, followed by the Ú/ Û buttons guntil PRO LOGIC appears in the Main Information Display Vand the PRO LOGIC indicator Glights up.

2.Press the Delay button i ÷ on the remote or front panel. The words

S DELAY TIME will appear in the Main Information Display Vand at the bottom of a video screen when the Semi- OSD display is in use.

To use the on-screen display system while making delay adjustments, press the OSD button s until the full-screen menu shown in Figure 4 appears on the screen.

M O D E : D O L B Y P R O L O G I C

S U R R O U N D : 2 0 M S

M A S T E R V O L U M E : Ð 2 0 D B

Figure 4

3.Press the Set button i 31.

4.Adjust the delay time by pressing the Ú/ Û buttons g on the remote or the Selector buttons 34on the front panel until the delay time figure calculated using the formula entered above appears in the display.

5.If only analog sources will be used, no adjustment is needed for the center-channel delay. In that case, press the Set button i 31 to enter the surround delay set- tings into the AVR’s memory. However, if you will be using digital sources and the calculations outlined above indicate that the center-channel delay requires an adjust- ment, continue with the following steps.

6.Before setting the center-channel delay time, make certain that a digital source has been selected. If a digital source is playing, COAX A or OPTICAL C will appear in the Information display V, along with the DIGITAL indicator F. If a digital source is already connected and playing, press the Delay button ÷28 so that the words C DELAY TIME appear in the Main Information Display

35 and proceed to step #10. If a digital source is not playing, follow steps 6 through 10.

7.Press the Set button i 31.

8.Select the Dolby Digital mode either by pressing the front panel Dolby Digital Selector (or by pressing the Surround Mode Selector 31 on the remote, and

then pressing the Ú/ Û buttons gon the remote until DOLBY D appears in the Main Information Display Vor in the on-screen display. Ignore any “NO DATA” message that may appear.

9.Press the Delay button i ÷ on the remote or front panel. The words S DELAY TIME appear in the Main Information Display V.

10.Press the Ú/Û buttons gon the remote once, so that C DELAY TIME appears in the Main Information Display

Vor in the on-screen display.

11.Press the Set button i 31.

12.Press the Ú/Û buttons g on the remote until the desired delay time for the center channel appears in the display.

13.Press the Set button i 31 to enter the setting into the AVR 500’s memory.

You have now completed the setup, adjustment and calibration of the AVR 500. You are now ready to enjoy the finest in music and home theater listening.

19SYSTEM CONFIGURATION

Image 20
Contents Page AVR 500 Audio/Video Receiver AVR 500 Audio/Video Receiver While complex digital systems are hard Description and FeaturesIntroduction Unpacking Safety InformationImportant Safety Information Preset Stations Selector * Tuner Mode Volume Control ÷ Delay Digital Input Selector ù Set ButtonFront Panel Controls Information Display Remote SensorCh Direct inputs ¤ as the listening source Front Panel Information Display Analog Source Indictor This indicatorNight Mode Indicator This indicator Rear Panel Connections £ AMRear Panel Connections AVR Selector Remote Control FunctionsForward/Reverse Transport Buttons z Night Mode ` Multi-Room OSD Button Press this button to view the on-screen displays Remote Control Functions Installation and Connections System InstallationAudio Equipment Connections Connect the analog output of a CD player to the CD inputsSystem and Power Connections Speaker Placement System ConfigurationSpeaker Selection and Placement System Setup Plug the Power Cable ¡ into an unswitched AC outletUsing the On-Screen Display Speaker ConfigurationOutput Level Adjustment CEN SpeakerDelay Settings Vor in the on-screen display Press the Set button i To set the delay times, follow these stepsPress the Set button i Operation Basic OperationDisplay Brightness Semi-OSDVolume Control Source SelectionSurround-Mode Selection Main Information Display V will now read VFD FullSurround Mode Chart Night Mode Digital Audio PlaybackSelecting a Digital Source Dolby DigitalPreset Tuning Recalling Preset StationsTuner Operation PCM Audio PlaybackOutput-Level Trim Adjustment Memory BackupTape Recording Channel Direct InputMultiroom Setup InstallationMultiroom Operation Multiroom OperationProgramming the Remote Programming the RemoteMacro Programming Volume Punch-ThroughProgrammed Device Functions Press the Volume Up button Reassigning Device-Control SelectorsFunction List Setup Code Tables TV Manufacturer/Brand008 024 030 065 101 143 160 038 070 083059 143 154019 047 169004 058 101 127 133 143 160Setup Code Tables VCR Manufacturer/Brand Setup Code Number054 133 140020 031 063 034 067Setup Code Tables CD Setup Code Tables DVDSetup Code Tables DVD/LD Setup Code Tables CableSetup Code Tables SAT Manufacturer/Brand Setup Code Number Remote Control ModelTroubleshooting Guide Processor ResetAmplifier is in protection mode Display brightness is turned offTechnical Specifications