REMOTE CONTROL FUNCTIONS
pSet/Enter Button: This button is used to enter settings into the AVR’s memory. It is also used in the setup procedures for delay time, speaker configuration and channel output level adjustment. When the RCP 2 is used to control the DVD, this button has the same function as the Enter Button as described in the DVD owner’s manual. Press it to activate the highlighted setting in a menu for either player setup or the disc currently being played.
qDigital Select/Eject Button: Press this button to assign one of the AVR’s digital inputs to a source. When the RCP 2 is used to control the DVD player, this button has the same function as the Eject (Open/ Close) Button as described in the DVD owner’s manual. Press it to open or close the disc drawer.
rNumeric Keys: These buttons serve as a 10- button numeric keypad to enter tuner preset positions. They are also used to select channel numbers when TV, VCR, Cable or SAT has been selected on the remote, or to select track numbers on the DVD, depending on how the RCP 2 has been programmed.
sTuner Mode/Repeat
tDirect/Angle Button: Press this button when the tuner is in use to start the sequence for direct entry of a station’s frequency. After pressing the but- ton, simply press the proper Numeric Keys rto select a station. When the remote is used to control the DVD, this button has the same function as the Angle Button as described in the DVD owner’s man- ual. Press it to change the viewing angle on discs equipped with that capability. It may also be used to rotate a JPEG still image as described in the DVD owner’s manual.
uTuning Up/Down/Pic
onds will cause the tuner to seek the next station with acceptable signal strength for quality reception. When MANUAL appears in the Lower Display Line ¯, pressing these buttons will tune stations in
vOSD Button: Press this button to activate the
wDolby Mode Selector/Zoom: This button is used to select from among the available Dolby* Surround processing modes. Each press of this button will select one of the Dolby Pro Logic* II modes or Dolby 3 Stereo, Dolby Pro Logic IIx or Dolby Virtual speaker, when available. When a Dolby
xDTS Digital Mode Selector/Random: When a
6.1Discrete encoding. When a DTS source is not in use, this button has no function. However, when used to control the DVD player, this button has the same function as the Random Button described in the DVD owner’s manual, enabling you to randomize play of audio tracks on CDs, MP3 and WMA discs.
yLogic 7 Mode Select/Video Off Button: Press this button to select from among the available Logic 7® surround modes. When used to control the DVD player, this button has the same function as the Video Off Button described in the DVD Owner’s Manual, and may be used to temporarily disable the video circuits during audio playback.
zSkip Chapter Up/Down Buttons: These buttons are preprogrammed to have the same function as the Skip Buttons as described in the DVD Owner’s Manual. Pressing these buttons will go to the beginning of the current chapter or track or the start of the next chapter or track, depending on whether a DVD or CD is playing. Press the button again to step back or forward through the available chapters or tracks on the disc. To step one frame at a time, press the Pause Button `, then select either the Skip Up or Skip Down buttons.
`Transport Controls: These buttons are pre- programmed with the same functions as the Search (Rev) ‹‹, Play ›, Search (Fwd) ››, Stop Í and Pause ±buttons on the DVD player. Press them to operate the respective transport functions. The Record button may be used when a VCR, tape deck, CDR or other recording device has been selected. The Forward and Reverse Search Buttons operate at fast speeds as described in the DVD owner’s manual when pressed repeatedly. To engage the Slow Search speeds, press the Pause Button first, then repeatedly press the desired Forward or Reverse Search Button.
28Stereo Mode Select/Display Button: When the button is pressed so that DSP SURR OFF appears in the Lower Display Line ¯, the AVR will operate in a bypass mode with true, fully analog, two- channel left/right stereo mode with no surround pro- cessing or bass management, as opposed to other modes where digital processing is used. When the button is pressed so that SURROUND OFF appears in the Lower Display Line ¯, you may enjoy a
5 CH STEREO or 7 CH STEREO to appear, and the stereo signal will be routed to all five (or seven) speakers. When used to control the DVD player, this button has the same function as the Display Button as described in the DVD owner’s manual. Press it to reduce the brightness of the DVD’s
29DTS Neo:6 Mode Select/Repeat: Press this button to select a DTS Neo:6 mode. These modes take a
30Macro Buttons: Press these buttons to store or recall a “Macro”, which is a preprogrammed sequence of commands stored in the remote. (See page 8 for more information on storing and recalling macros.)
REMOTE CONTROL FUNCTIONS 5