Revox Recontrol M207 user manual Appendix C, Troubleshooting Tables

Page 75

Appendix C

Troubleshooting Tables

Problem		Solution

LCD does not show	•	Batteries may be dead.
anything when you touch it.	•	Replace the batteries with three new AAA Alkaline batteries.
	•	Check the batteries are properly installed.

The Re:control M207	•	Make sure that the desired device on the Re:control M207 LCD
doesn’t operate a device.		panel has been selected.
	•	Move closer to the device. The maximum operating distance is
		approximately 10 meters (30 feet).
	•	Ensure that you are aiming the Re:control M207 directly at the
		device and that there are no obstructions between the
		Re:control M207 and the device.
	•	Ensure that you have correctly used the learning function to
		configure the device or the Pre-Programmed Code has been
		properly done.
	•	Re-teach the malfunction key.
You cannot operate a	•	Make sure that your Re:control M207 has correctly learning the
device even after teaching		target device’s remote control code.
the device using the	•	Delete the device data from the Re:control M207 and carry out
learning function.		the learning function again.
	•	Make sure you did not program more than one remote for a
		given device.
You see an “error” display	•	Make sure you hold the target remote’s key till the screen
on the LCD screen during		displays OK or Error on the screen.
the learning procedure.	•	Make sure the two remotes are not too close or too far apart –
		keep them about 2~4 inches (5~10 cm) apart, and your device
		remote control is aiming directly at the Re:control M207’s
		learning eye.
You see an “error” display	•	The key that you pressed has not been taught.
during operation.	•	Teach the key using the learning procedure.

IR Learning is not	•	Replace batteries in the Re:control M207 and the remote you
successful.		are trying to configure.
	•	Keep the learning distance between the remote control and the
		Re:control M207’s learning eye to about 2~4 inches (5-10cm).
	•	Do not use the learn function near an incandescent lamp.
	•	Memory capacity is full (56 keys for each of eight models).
	•	The learning process has no errors, but you still can’t control

72

Image 75

Contents Recontrol M207 Preface About this manualCopyright Page Table of Contents Menus Introducing Recontrol M207 Unpacking the Recontrol M207 Recontrol M207 FeaturesRemove battery cover Installing BatteryTurning the touch screen on Precautions for using batteryFront side of the recontrol M207 Identifying ComponentsRear side of the Recontrol M207 Battery compartmentSetup mode function Device normal function Direct Access Buttons Rubber ButtonsLCD Touch Screen Precautions of using touch screenTouch screen buttons Touch screen keysMain Menu Basic Information Layout Setup Menu Layout Introducing Recontrol M207 Re-calibrate the screen Quick StartDate / Time setting Device setting Quick Start How to Set Your Recontrol M207 Add a DeviceCreate a new device How to Set Your Recontrol M207 Pre-code Load the codes for the newly-added deviceHow to Set Your Recontrol M207 Learning How to Set Your Recontrol M207 Learning Learning fail Successfully Add a Soft KeyHow to Set Your Recontrol M207 Add a Text Re-label a Device, Key or Text Select Icons Re-size a Device, Key or Text Recontrol M207 User’s Manual Delete a Device, Key or Text Pre-code How to Set Your Recontrol M207 Recontrol M207 User’s Manual Learning Recontrol M207 User’s Manual Learn a Cycle key Recontrol M207 User’s Manual Delete Device/Key codes Macro Create a MacroPlease press the button to confirm your decision An Example to Add a Macro Create a Timer Macro Timer MacroRecontrol M207 User’s Manual Delete Your Timer Macro Re-label Your Timer Macro View Your Timer Macro Add the favorite channel keys Create Your Favorite ChannelsSet these Macros as your favorite channels Menus SettingPower TimeContrast LCD Off Light SensitivityLight Period Reset MotionWelcome Page 2. Please use Delete Key LayoutAdd Text Re-sizeCode Setting Timer Macro Re-labelView Duplicate Recontrol M207 User’s Manual Calibrate Install USB Cable and Software Install Reconnect USB cableInstall the Driver Install USB Cable and Software Install Upgrade Tools Install USB Cable and Software Upgrade Vmcu Firmware and Vmcf Pre-programmed Codes Install USB Cable and Software Recontrol M207 User’s Manual Appendix a FeaturesCD, AUX SpecificationsAppendix B Optional AccessoriesAppendix C Troubleshooting TablesTroubleshooting Tables