Dish Network VIP612 manual Using the Recover Button

Page 13

 

 

 

 

 

 

 

 

Remote Control Setup

 

 

 

 

 

 

 

 

 

The Recover Button

 

 

 

 

 

2

3

 

 

 

 

 

1

 

 

Press the

4

 

 

 

 

 

3 button

5

6

 

 

 

 

 

 

 

 

 

 

AUX

 

 

 

 

 

 

 

 

 

 

 

 

Receiver CAID

R0079256789-30

 

Press and hold the

 

 

 

 

 

Model ID

ViP612 CVR-SD

 

 

 

 

 

 

 

 

Smart Card ID

S1907972574-12

AUX Mode buttton until all

 

 

 

 

Billing & Programming

1-800-333-DISH(3474)

 

 

 

 

Software Version

DNASP206 Dsh689

 

 

 

 

 

 

 

AEE2WAND-N

 

 

 

 

 

 

 

Boot Strap Version

1010WAND

 

 

 

 

 

 

 

 

Technical Assistance

1-800-333-DISH(3474)

 

Mode butttons light up

 

 

 

 

Internet Address

dishnetwork.com

 

 

 

 

Press

Remote Address

IR/UHF Pro Band A

 

 

 

 

Receiver Mode

Single Mode

 

 

 

 

 

Enter remote

Press POUND

 

Location ID

87940875:00000004

 

 

 

 

 

 

 

Help

Done

Cancel

 

(Button will Flash)

address from step

(AUX button

RECORD

 

 

 

 

 

 

 

Display System Information

 

 

 

one

will flash 3 times)

 

screen and note the

 

 

 

 

 

 

 

Remote Control Address

 

 

 

 

 

 

1Turn on the other receiver and display the System Info screen as described in that user’s guide.

Write down the remote control address:

2Press and hold AUX until all the other mode buttons light up, and then let go of the button. AUX flashes.

3Press the 3 button.

4Use the NUMBER PAD to enter the address you wrote in step 1.

5Press POUND (#). AUX blinks three times.

6Press RECORD to ensure the address in the remote matches the address on the receiver.

THE RECOVER BUTTON

Use RECOVER if you accidentally change the TV channel or video input and have a snowy, blue, or black screen on your TV. When you press RECOVER as described below, the remote control sends commands to your TV to change channels or video inputs to get back to watching satellite programming. This procedure works only if you have accidentally changed the TV channel or video input. It does not recover lost satellite signal (see Troubleshooting Tables on page 100 for information on solving problems).

Note: The remote control must be programmed to operate the TV (and VCR, if applicable) for RECOVER to work as described. RECOVER will first try to tune your TV to channel 3, then channel 4, and then other video inputs with each press of RECOVER. You may need to press RECOVER multiple times to recover your satellite TV video.

Using the Recover Button

To use RECOVER, the remote control must be programmed to operate the TV and, if installed, the VCR.

73

Image 13
Contents Remote Control Setup Checking the Remote Control Address Changing the Remote Control AddressChanging the Remote Control from UHF Pro to IR Confirming Remote Control OperationChanging the UHF Frequency Using the A/B Switch Adjusting the Remote AntennaInstalling a UHF Attenuator Limited Mode Remote Control ModesCombination Devices Instructions Additional Information Setting Up Using Device Code TablesSetting Up Using Device Codes Scan Checking the Device Codes Chapter To Use a Tuner or Amplifier’s Volume Control Switching Between TV and Tuner/Amplifier Volume ControlControlling a Tuner or Amplifier Page Recover Button Using the Recover ButtonQuestions