Kathrein UFS 710sw, UFS 710si “Current” View, Epg - Electronic Programme Guide, Selection options

Page 39

Selection options:

EPG - ELECTRONIC PROGRAMME GUIDE

Selection options:

-	(red) button	Calls up the plan recording (display of all pre-programmed recordings)
-	button	Jump the “Current” view forwards by 15 minutes
-	" (yellow) button	Call up a preview of the currently highlighted channel
-	# (blue) button	Call up the category selection (sorting the programmes by categories such as
		movies, sport, series ...)
-	& button	(P+) jump forwards 24 hours in the EPG, (P-) jump backwards 24 hours in
		the EPG (e.g. into “Current” and into “Preview”)
-	button	Selects the currently highlighted channel in all views. Pressing the button
		or the	button again closes the EPG and the selected channel is shown
		again on the TV screen
-	(red dot) button	Adds a programme to the recording settings
-	button	Search for a particular programme or programme content (input the search
		expression using the numeric pad on the remote control, see also the section
		“Operating instructions”, “Alphanumeric input”)
-	button	If present, shows further information on the selected programme.
Navigation within each		view	is always performed using the cursor buttons ().

The buttons allow you to select individual channels/programmes, and the buttons allow you to scroll from page to page of the currently selected list.

Pressing the button or the button exits the EPG again and returns to the TV picture.

You will see information on the current or next following programmes in the EPG only if it is supplied by the channel provider. If no EPG data are available the receiver, instead of showing information on the current programme, shows the message “No data available!”.

“CURRENT” VIEW

The “Current” view can be called up at any time in EPG by pressing the ! (green) button. This is then automatically displayed every time the EPG is started (see screenshot “Calling up EPG”).

In the “Current” view you see all channels displayed in the order of the overall channel list. Provided that EPG data has been supplied by the channel provider, the receiver shows for each channel the current programme being shown, with start time, ﬁnish time, and progression bar.

You can use the cursor buttons () or the keypad buttons to select the desired channel and if

39

Image 39

Contents DVB Satellite Receiver UFS 710si/710swOperating manual englisch PREFACE DISPOSAL INSTRUCTIONSUsed batteries are special waste SWITCHING OFF THE RECEIVER AND UPDATING THE EPG IMPORTANT INFORMATIONREFERENCE NOTE ON AUDIO MPEG INC. AND S.I.SV.EL, S.P.A RECEIVER FEATURES/SCOPE OF SUPPLY CONTENTSCONTENTS SAFETY INSTRUCTIONS - IMPORTANT NOTESUSING THE FRONT PANEL SETTINGSSERVICE MENU CONNECTING UP THE VIDEO/PVRSAFETY INSTRUCTIONS - IMPORTANT NOTES PRODUCT PACKAGE RECEIVER FEATURES/SCOPE OF SUPPLY CONTROLS, DISPLAYS AND CONNECTIONSVIEW OF FRONT PANEL FLAP FOLDED DOWN VIEW OF REAR PANELRECEPTION REQUIREMENTS CONNECTING THE UNIT SAT-IF CONNECTIONSRECEPTION SYSTEM PRESETS CONNECTION AND SET-UPOPTICAL/ELECTRICAL DIGITAL OUTPUT INSERTING BATTERIES INTO THE REMOTE CONTROLTV AND VIDEO RECORDER CONNECTION AUDIO CONNECTION REMOTE CONTROL RC The “Connection examples” section provides a sample conﬁguration FIRST INSTALLATION GeneralTV aspect ratio When doing this, refer to the operating instructions for your TV setSystem Continue with the relevant section of First InstallationPicture format TV-SCART-OutputFIRST INSTALLATION DiSEqC1.0 Number of SatellitesSatellite and Position Test transponder LNB TypeSatellite and position FIRST INSTALLATION SIMPLE LNBTest transponder Conﬁgure satellites FIRST INSTALLATION Single-cable systemFIRST INSTALLATION Single-cable system FIRST INSTALLATION Single-cable system Automatic No frequency can be used by more than one receiverThe receivers would interfere with each other FIRST INSTALLATION Single-cable system Manual Connected equipmentSelection “user-deﬁned” Test connection Selection “UAS 481” or “EXR 551” Selection “EXR 552” Selection “EXU 908” Selection “4 subscriber” Selection “8 subscriber” Network Search FIRST INSTALLATION Channel searchExecute Channel search Channel Search ModeLocal time offset FIRST INSTALLATION Channel Search/Date and TimeMENU CONCEPT OPERATING INSTRUCTIONSMENU TREE Main MenuLANGUAGE SETTING - OSD KEY TO RECEIVER DISPLAY SYMBOLSALPHANUMERIC INPUTS CALLING UP THE OPTIONS CHANNEL ON-SCREEN DISPLAYS OSDCHANNEL MESSAGES PROGRAMME INFORMATIONERROR SIGNALLING OPTION SELECTIONCHANNEL LIST - TV/RADIO Selection and sorting options Search functionInfo on CALLING UP THE EPG EPG - ELECTRONIC PROGRAMME GUIDESelection options “CURRENT” VIEWPREVIEW VIEW PROGRAMME LISTINGS CATEGORIES VIEW SEARCH FUNCTION ADDITIONAL INFORMATION i BUTTON Programme present in the EPG RECORDING TIMERrecorder” using the cursor buttons RECORD DAILY RECORD ONCERECORD USER-DEFINED RECORD WEEKLYSERIES RECORDING PLAN RECORDING Store your card and PIN code securely when not in use COMMON INTERFACEIMPORTANT INFORMATION INSERTING THE SMARTCARD AND THE CA MODULEConﬁrmation is by pressing the button VIDEOTEXT TELETEXT SELECTION OF THE LIST/CHANNELS TO BE EDITED EDIT CHANNEL LISTSkip EDITING LISTS/CHANNELSMove DeleteSKIP CHANNELS “LAST FUNCTION” MEMORYMOVE CHANNELS DELETE CHANNELSLOCK CHANNELS COPY CHANNELS TO THE FAVORITES LISTSTART BLOCKSELECTION SELECTING SEVERAL CHANNELS EDIT FAVORITES LISTS Remove from the Favorites ListRename Favorites List START BLOCKSELECTION HIGHLIGHTING SEVERAL CHANNELS RENAME FAVORITES LISTAUTOMATIC CHANNEL SEARCH SEARCH CHANNELS CHANNEL SEARCHSatellite a scan of whatever type MANUAL CHANNEL SEARCHselection using the buttons AfterTransponder Frequency CHANNEL SCAN WITH SERVICE ID Service ID PARENTAL CONTROL LOCK MAINMENULOCK SET-TOP-BOX Conﬁrm the change of PIN code by pressing the button DEFINE NEW PIN CODESETTINGS TV-SCART-OUTPUT TV SETTINGSTV ASPECT RATIO PICTURE FORMATAUTO DOLBY DIGITAL OUTPUT CUSTOMIZE SCREEN MENUVCR-SCART-OUTPUT TELEVISION SYSTEMCHANNEL OSD DURATION DISPLAY VOLUME BARADJUST MENU ON TV FUNCTIONAL RANGEAutomatic clock change ANTENNA CONFIGURATIONDATE AND TIME COMMON INTERFACEUPDATE SOFTWARE SERVICE MENUChannel List Update SoftwareRESTORE FACTORY DEFAULT SETTINGS CONNECTING UP THE VIDEO/PVR RECORDINGPLAYBACK button USING THE FRONT PANELBACKUP OPERATION TV/R buttonTECHNICAL APPENDIX FEATURESPower consumption power/standby Video resolutionPower Supply Power supply voltageSCART SOCKET ASSIGNMENT VHS/S-VHS SWITCHINGCinch CONNECTION EXAMPLEDolby Digital system LWL CinchEXR 501/551/552 EXAMPLES single-cable systemsOvervoltage protection KAZ 11/KAZ Single-cable feed system EXR 1581/2581 Single-cable matricesSat IF Quatro LNB UAS 484/584 Sat IF Single-cable matrixDISEQC COMPONENTS SHORT TECHNICAL GUIDECHANNEL PACKAGE DISEQCVITERBI RATE SYMBOL RATETRANSPONDER VIDEO-BIT-RATEUFOmini GLOSSARYCause TROUBLESHOOTINGSERVICE Problem936.3200/D/0209/ZWT - Technical data subject to change