Woods Equipment BH6500 manual Operation, Maintenance

Page 5

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

check and comply with these instructions may result in serious injury or death.

νRemove seat and upper support assembly before installing or removing backhoe from tractor. Failure to comply may result in equipment failure and/or personal injury.

νIf tractor is equipped with draft sensing control, set control to “HEAVY” (minimum sensitivity) posi- tion.

νOn tractors equipped with optional “Draft Con- trol Hitch,” you must install the “Draft Lockout” (provided in sub-frame kit) into position as shown. Failure to install the “Draft Lockout” will allow upper hitch to move during backhoe operation and could result in operator injury.

νMake sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.)

νA minimum 25% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, tractor could tip over, causing personal injury or death. The weight may be attained with a loader, front wheel weights, ballast in tires, or front tractor weights. Weigh the tractor and equipment. Do not estimate.

OPERATION

νDo not allow bystanders in the area when oper- ating, attaching, removing, assembling, or servic- ing equipment.

νBefore operating, make sure stabilizer pads are lowered firmly to the ground. Stabilizer arms pro- vide support for the backhoe and support for the backhoe mounting brackets.

νDo not operate equipment while under the influ- ence of alcohol or drugs.

νAlways comply with all state and local lighting and marking requirements.

νDo not allow riders. Do not lift or carry anybody on the power unit or attachments.

νThe only time the backhoe may be operated from a position other than the operator seat is dur- ing backhoe attachment and removal. Operator must

•Read Sub-Frame Mounting Kit Manual instructions on attaching and removing back-

hoe and use extreme care

•Always stand between rear tire and backhoe stabilizer arms or along side of tractor to avoid being trapped should the boom swing control be accidentally activated.

νNever leave equipment unattended with engine running or with bucket in raised position. Always engage swing and boom transport locks, relieve system pressure by operating controls, and remove ignition key before leaving equipment.

MAINTENANCE

νRefer to backhoe manual and follow all mainte- nance safety rules and instructions.

νDo not modify or alter or permit anyone else to modify or alter the equipment or any of its compo- nents in any way.

νYour dealer can supply original equipment hydraulic accessories and repair parts. Substitute parts may not meet original equipment specifica- tions and may be dangerous.

νAlways wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head.

νDo not allow bystanders in the area when oper- ating, attaching, removing, assembling, or servic- ing equipment.

νMake sure attachment is properly secured, adjusted, and in good operating condition.

νKeep all persons away from operator control area while performing adjustments, service, or maintenance.

νBefore working on backhoe, extend boom and dipperstick and place bucket on ground. Make sure that all system pressure has been relieved by oper- ating controls before performing maintenance or service or before disconnecting any hydraulic lines.

νTighten all bolts, nuts and screws to torque chart specifications. Check that all cotter pins are installed securely to ensure equipment is in a safe condition before putting unit into service.

ϖ

BH6500/7500 SFMK 11/1/00

SAFETY 3

Page 4 Page 6
Image 5
Page 4 Page 6
Contents 59756 To the Dealer Model #59757 Sub-Frame Mounting Kit Date of PurchaseTable of Contents Installation Safety RulesTraining PreparationOperation MaintenanceBackhoe SUB-FRAME Installation InstallationTractor Preparation SUB-FRAME Installation Cont’dRear Hanger Bracket Assembly Install Rear Hanger BracketsModify Loader Mounts Install Mid-mount BracketFor tractors equipped with Woods 1006 Loader Install Right & Left Reinforcement BracketsCrossmember Bracket Installation Install CrossmemberSub-frame Fit-up typical Sub-Frame Fit-UpSub-frame attached to backhoe Attaching Sub-Frame to BackhoeMount Bracket to Pump Kit Pump Bracket Assembly TypicalMount Sub-Frame & Backhoe to Tractor SUB-FRAME & Backhoe to TractorConnect Hydraulic System SUB-FRAME & Backhoe to Tractor Cont’dStore Hydraulic Pump Remove Backhoe With Sub-Frame#59757 SUB-FRAME Mounting KIT PartsPart QTY Description #59757 SUB-FRAME Mounting KIT Parts ListSAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartWarranty Model No Part Warranted Duration Woods Equipment Company. All rights reserved

BH6500 specifications

The Woods Equipment BH6500 is a robust and versatile hydraulic backhoe designed for a variety of construction and landscaping tasks. Renowned for its durability and performance, the BH6500 offers a blend of efficiency and flexibility, making it an excellent choice for contractors, landscapers, and homeowners alike.

One of the standout features of the Woods BH6500 is its impressive digging depth. With a maximum digging depth of approximately 7 feet, the backhoe is designed to tackle deep excavations, trenching, and utility installations. The ability to gain access to deeper areas enhances its functionality for both commercial and residential projects.

Powering the BH6500 is a series of advanced hydraulic technologies that ensure smooth and precise operation. The hydraulic system provides exceptional breakout force, enabling users to lift and move heavy materials with ease. This capability is essential for digging, lifting, and backfilling applications, allowing operators to complete tasks quickly and efficiently.

The BH6500 is equipped with a variety of bucket options, including standard buckets, ditching buckets, and specialized attachments. This versatility allows users to customize the backhoe based on their specific needs, whether it’s digging, lifting, or grading. The easy change-out of attachments further adds to its convenience, minimizing downtime during projects.

In terms of compatibility, the Woods BH6500 is designed to be used with a wide range of tractors, significantly enhancing its usability. This feature allows users to maximize the investment in their existing equipment while expanding their operational capabilities.

Comfort and safety are also prioritized in the design of the BH6500. The ergonomic control layout and operator-friendly features improve ease of use, allowing operators to focus on their tasks without unnecessary strain. Safety mechanisms are integrated to protect users during operation, ensuring peace of mind while working on demanding jobs.

Overall, the Woods Equipment BH6500 is characterized by its strength, versatility, and advanced technology. Whether you are engaged in landscaping, construction, or agricultural work, this hydraulic backhoe provides the necessary power and functionality to complete tasks efficiently, making it a reliable partner for any project. With its array of features, the BH6500 stands out as a valuable asset in the world of machinery and equipment.
Top Page Image Contents