Yamaha DVD-C920 owner manual Preparation, To turn Power Press, To open Disc Tray Load Discs

Page 15

To play a disc properly, you need to adjust the formats of audio and video signals output from this unit in accordance with the

equipment connected to this unit. See p.25 to 27.

•If your AV amplifier does not incorporate DTS decoder and you have connected this unit and the amplifier through

digital terminals, please make sure that the 'DTS Digital Surround' at 'Audio' SETUP MENU is set to PCM (factory-

setting). Otherwise, unprocessed digital signals will be output and its noise could damage your ears and your speakers.

•Preparation

Select DVD as the input source on your AV amplifier.

U

Press

POWER

to turn

the power

on.

[]

Press

-_ (or

OPEN/CLOSE)

to open

the

disc

tray.

[]

Load

discs.

4 (PLAY)

Use the disc

guides

(numbered,

1 to 5) to

align

the

discs

correctly.

[]

Press

_

(PLAY).

The disc tray closes and playback starts. This unit plays

all discs on the tray in sequence.

• If necessary, select a desired disc using DISC SKIP or one of the

DISC

1, 2, 3, 4 or 5 buttons.

• When

a menu

screen

appears

_

_

_:

Disc tray

See 'Using a Disc's Menu' in p. 14.

• When this unit finishes playing a DVD, this unit stops playback or

shows the menu screen and does not start playing the next disc.

• This unit

cannot

play

a CD-R

or CD-RW

disc

unless the disc has

been finalized. Please make sure to finalize the disc on the CD

recorder

before

playing

it

on

this

unit.

(PLAY)

11

Image 15

Contents Ooo0 Explanation of Graphical Symbols FCC Information for US customers only Iiii iiii Features A. and Canada models Australia model Remote controlBatteries AA, R06, UM-3 ?rnD@MP3 playback Region management informationPlay Front Panel Remote ControlDisc tray Playxchange p.12 StopCursor buttons, Enter SET UP p.25Group p.15 Display panel Menu p.14Track rdR Repeat mode indicatorsAudio type indicators Disc type indicatorsWithin approximately 6 m Feet @@@@6CH Discrete terminals Required Audio settings See p.25, 26Digital outputs Analog outputs@Component Video terminal Lilil*liPliTThese terminals are used for custom installation system that To open Disc Tray Load Discs To turn Power PressPreparation PressTo stop playback To select a specific discAfter operation Pause SkipTo select a specific track rdR SearchVideo CDs playback control PressTOP Menu or Menu during playback toTo play a track on a specific group To play a bonus groupPress Group Angles Ove you JetaimeAudio tracks SubtitlesProgram repeat rdR Random-sequence repeatPress Repeat during playback To cancel random mode To cancel A-B repeatPress numeric buttons to select the track To cancel the programmed tracksTo exit programming mode Press Disc l m5 to select the discPress Enter To recall a bookmarked sceneTo clear a bookmark Press MarkerTo change the menu bar position Press the cursor buttons A,V to change settingSignal type/data Angle numberLanguage Repeat p.18 Play mode menuDisplay menu Audio menuTransfer Mode Adjusting the screen position when using progressive outputDigital picture mode To change the user modePress Cursor Buttons To select To get out from the setup menu modePress SET UP while playback is stopped To go back to the previous screenRatings Video Audio ItemsSubtitle MenusDemo DVD-Video ModeDisplay Others On-Screen MessagesSetting method To change settingsEnter 4-digit number with numeric buttons and press Enter Speaker balance @ Output mode @Delay time @ To exit the speaker setting modeThis unit fails to turn On when PowerSwitch is pressed This unit does not work Refer toPossible Cause Returning setup menu to the factory-settingAudio Section Video SectionGeneral