If this unit fails to operate normally, check the following points to determine whether the fault can be corrected, or if the fault
is not listed in the PROBLEM column, disconnect the power code and contact your authorized YAMAHA dealer or service center.
Refer to
PROBLEM |
|
|
| POSSIBLE | CAUSE |
|
|
|
|
|
| WHATTO | DO |
|
| Page | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This unit fails to turn | The | power | cord | is | not | connected | or | the plug | Firmly |
| connect | the | power | cord. |
|
|
| |||||
on when | the POWER | is not completely | inserted. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
switch is pressed. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This unit does not work | This | unit | is | affected | by | an | external |
| shock | Turn | the power off and disconnect |
| the power | |||||||||
normally. |
|
|
| |||||||||||||||||||
| (lightning, |
| excessive | static | electricity, |
| cord. After | about 30 seconds have | passed, |
| ||||||||||||
|
| incorrect | operation, | etc.) |
|
|
| connect | the | power | and operate the unit again. | |||||||||||
Playback | does not | The | disc | is | damaged. |
|
|
|
| Check | the disc carefully; | replace | it | if |
| |||||||
start. |
|
|
|
|
|
|
|
|
|
|
| necessary. |
|
|
|
|
|
|
|
| ||
|
| There | is | moisture | on the laser pickup. | Wait | 1 to 2 hours after switching | the unit on | ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
| before trying | to play | a disc. |
|
|
| |||||
|
| The | disc | has been | loaded | upside | down. | Reload | the | disc with | the | label side | facing | up. | ||||||||
|
| The | disc | is dirty. |
|
|
|
|
| Clean | the disc. |
|
|
|
|
| 3 | |||||
No picture. | Incorrect | video | connections. |
|
| Connect | this unit and other equipment | 9 | ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
| properly. |
|
|
|
|
|
|
|
| ||
|
| Input | selection | at your | AV | amplifier | or your | Set the | input | to the | right | position. |
|
|
| |||||||
|
| video monitor is not the one connected to this |
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
| unit. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| VIDEO | OFF is functioning. |
|
|
| Press | VIDEO | OFF | to cancel the feature. | 15 | |||||||||||
|
| (U.S.A. | and | Canada | models) |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
| If you play | PAL | system | 'This |
|
|
|
|
|
|
|
|
|
|
| ||||||
Picture appears incorrectly.
Play is delayed, or starts at the wrong place.
disc is PAL system. The output is sound only'
may appear on the monitor. Picture is not
available because the disc's video signal system is different.
Incorrect 'TV aspect' setting.
A VCR is connected between this unit and the video monitor.
(U.S.A. and Canada models)
PROGRESSIVE is turned on even though the
connected monitor cannot receive the
progressive signals.
(U.S.A. and Canada models)
Due to the editing method or material used on
a DVD, ghosting may occur with progressive output.
The disc may be scratched or damaged.
Select | the right position. However, it may | be | 26 | |
difficult to adjust many |
|
| ||
widescreen format to fit perfectly in your 4:3 |
| |||
video | monitor. |
|
|
|
Connect this unit's video outputs directly | to | 9 | ||
your video monitor or to your AV amplifier |
| |||
and then to a video monitor. |
|
|
| |
Turn | off the PROGRESSIVE | feature. |
| 14 |
Turn | off the PROGRESSIVE | feature. |
| 14 |
This unit does not recognize discs ('No disc' appears on the display, or the display shows the status when no disc is loaded).
No sound.
The disc(s) is not placed properly. | Place the disc(s) correctly | along the guide(s). |
Incorrect cable connections. | Connect | the cables | properly. If the problem | 8 |
| persists, | the cables | may be defective. |
|
Incorrect amplifier operation. | Set the amplifier controls to the correct input | |
| selection. |
|
30