Yamaha DVD-C920 owner manual Returning setup menu to the factory-setting, Possible Cause

Page 35

PROBLEM

No sound when playing a disc encoded with DTS.

No sound from some speakers.

Sound distorted.

Sound 'skips'.

Sound 'hums'.

Noise from a nearby tuner.

Noise from inside of the unit.

The remote control does not work.

Audio track and/or

subtitle language is not the selected one.

No subtitles.

Angle cannot be changed.

The password for setting parental level has been forgotten.

POSSIBLE CAUSE

Incorrect setting(s) at the audio section of

'Setup menu' on this unit or at 'input mode' on your amplifier.

With some DVD-Audio, output channels are specified by the disc.

Incorrect 'Speaker settings'. (when 6CH DISCRETE outputs are connected to your amplifier)

Audio output form this unit becomes two channels when the virtual surround feature is

on.

Virtual surround effect is emphasized too much.

This unit is being subjected to vibrations or impacts.

The disc is dirty.

Incorrect cable connections.

The tuner is too close to the unit.

The disc maybe warped.

The batteries are weak.

Direct sunlight or lighting (from an inverter

type of fluorescent lamp, etc.) is striking the remote control sensor of this unit.

The disc does not contain the language you have selected.

The disc does not have subtitles.

Subtitle is turned off.

The disc or the scene being played does not support multi-angle.

IiloIq'l_-'Flil,llli'l_

Refer to

WHAT TO DO

Page

Select proper settings.

26, 27

Change the settings to suit your speaker

29

 

system.

 

 

Turn virtual surround mode off.

23

Turn virtual surround mode off.

23

Relocate

the unit.

 

Clean the disc.

3

Securely

connect the audio cables. If the

8

problem persists, the cables may be defective.

 

Place the tuner and the unit farther apart.

 

Replace

the disc.

 

Replace all batteries with new ones.

7

 

Relocate

the unit.

7

Show subtitles by pressing SUBTITLE or

16

using on-screen menu.

 

Clear all settings on the setup menu. See 'Returning setup menu to the factory-setting' below this table.

•Returning setup menu to the factory-setting

While playback is stopped, press and hold 00 (PAUSE),

'Initialized' appears on the video monitor. All settings

and then DISC SKIP and PLAYXCHANGE on the front panel until on the setup menu return to the factory settings.

31

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Ooo0 Explanation of Graphical Symbols FCC Information for US customers only Iiii iiii Features A. and Canada models Australia model Remote controlBatteries AA, R06, UM-3 ?rnD@MP3 playback Region management informationPlay Front Panel Remote ControlDisc tray Playxchange p.12 StopCursor buttons, Enter SET UP p.25Group p.15 Display panel Menu p.14Track rdR Repeat mode indicatorsAudio type indicators Disc type indicatorsWithin approximately 6 m Feet @@@@6CH Discrete terminals Required Audio settings See p.25, 26Digital outputs Analog outputs@Component Video terminal Lilil*liPliTThese terminals are used for custom installation system that To open Disc Tray Load Discs To turn Power PressPreparation PressAfter operation To stop playbackTo select a specific disc Pause SkipTo select a specific track rdR SearchVideo CDs playback control PressTOP Menu or Menu during playback toPress Group To play a track on a specific groupTo play a bonus group Angles Ove you JetaimeAudio tracks SubtitlesPress Repeat during playback Program repeat rdRRandom-sequence repeat To cancel random mode To cancel A-B repeatPress numeric buttons to select the track To cancel the programmed tracksTo exit programming mode Press Disc l m5 to select the discPress Enter To recall a bookmarked sceneTo clear a bookmark Press MarkerTo change the menu bar position Press the cursor buttons A,V to change settingLanguage Signal type/dataAngle number Repeat p.18 Play mode menuDisplay menu Audio menuTransfer Mode Adjusting the screen position when using progressive outputDigital picture mode To change the user modePress Cursor Buttons To select To get out from the setup menu modePress SET UP while playback is stopped To go back to the previous screenRatings Video Audio ItemsSubtitle MenusDemo DVD-Video ModeDisplay Others On-Screen MessagesEnter 4-digit number with numeric buttons and press Enter Setting methodTo change settings Speaker balance @ Output mode @Delay time @ To exit the speaker setting modeThis unit fails to turn On when PowerSwitch is pressed This unit does not work Refer toPossible Cause Returning setup menu to the factory-settingGeneral Audio SectionVideo Section
Top Page Image Contents