Symphonic SC313E Clock SET UP Auto / Manual, ADDING/DELETING Channels, Manual Clock Setting

ADD / DELETE

3After scanning

The tuner stops on the lowest memorized channel.

NOTES:

•If there is no TV signal input, “NO TV SIGNALS” will appear on the display after the completion of channel scanning.

•The unit may recognize TV channels to be CATV channels if reception condition is poor. In this case, check the antenna connection and try “AUTO CH PROGRAMMING” again when reception condi- tions are better.

•Channel memory programming is NOT neces- sary when connected to a cable box or satellite box. Just select the channel for the cable box or satellite input (ex. CH3) on the unit, then select your desired channel on the cable box or satel- lite box.

ADDING/DELETING CHANNELS

The channels you no longer receive or seldom watch can be deleted from the memory. (Of course, you can add the deleted channel into the memory again.)

1 Select “CHANNEL SET UP”	– M E N U –
Hit [MENU].	PICTURE CONTROL
	TIMER PROGRAMMING
Press [PLAY/K] or [STOP/L] to	SETTING CLOCK
	B CHANNEL SET UP
point to “CHANNEL SET UP”,	USER’S SET UP
	LANGUAGE [ENGLISH]
	V-CHIP SET UP
then hit [F.FWD/ B].	CAPTION [OFF]
	ZERO RETURN
	TIME SEARCH
2 Select “ADD/DELETE CH”	– CHANNEL SET UP –
Press [PLAY/K] or [STOP/L] to	B ADD / DELETE CH (CATV)
point to “ADD/DELETE CH”, then	AUTO CH PROGRAMMING
hit [F.FWD/ B].

3Enter the desired channel number

Press [PLAY/K] or [STOP/L] or the Number buttons until your

desired channel number appears. 08

(You can also press [CHANNEL K/L] to enter it.)

•You must precede single-digit

channel numbers with a zero (Example: 02 ... 09).

•When selecting cable channels which are higher than 99, hit [+100] first, then press the last two digits. (Example: to select channel 125, first hit [+100] then hit [2] and [5].)

4Delete (or add) it from (or into) memory

Press [REW/s] or [F.FWD/B]. The channel number changes to light red. The channel is deleted from memory.

•To delete another channel, repeat steps 3 to 4.

•If you press [REW/s] or [F.FWD/ B] again, the channel is memorized again.

Added channel: Light blue

Deleted channel: Light red

5Exit the channel setup mode

Hit [MENU] to returns to TV mode.

NOTE:

•To confirm that channel(s) has been deleted or added, press [CHANNEL K/L].

CLOCK SET UP

(AUTO / MANUAL)

The unit clock must be set correctly so that VCR timer recording is possible. It is suggested that the clock be set manually when first setting up the unit, then set to [ON] the auto clock setting which will periodically correct the setting if necessary.

NOTE:

•If you cannot receive a station with time signals, auto clock setting cannot be performed. Use manu- al setting only.

MANUAL CLOCK SETTING

Make sure ...

•The unit must be turned on.

In the example below, the clock is to be set to:

DATE	May 5th, 2005
SETTING TIME	5:40PM
1 Select “SETTING CLOCK”		– M E N U –
Hit [MENU].		PICTURE CONTROL
		TIMER PROGRAMMING
Press [PLAY/K] or [STOP/L] to		B SETTING CLOCK
		USER’S SET UP
point to “SETTING CLOCK”, then		CHANNEL SET UP
		LANGUAGE [ENGLISH]
		V-CHIP SET UP
hit [F.FWD/ B].		CAPTION [OFF]
		TIME SEARCH
		ZERO RETURN

2Select “MANUAL CLOCK SET”

Press [PLAY/K] or [STOP/L] to	– SETTING CLOCK –
point to “MANUAL CLOCK SET”,	AUTO CLOCK	[ON]
then hit [F.FWD/ B].	AUTO CLOCK CH SEARCH
	B MANUAL CLOCK SET	[ 02 ]
	AUTO CLOCK CH
	D.S.T.	[OFF]

3 Select the month

– MANUAL CLOCK SET –

Press [PLAY/K] or [STOP/L] until

your desired month appears.	MONTH DAY		YEAR
	0 5	/ – – – – – – – – –
(Example: May → “05”)	HOUR	MINUTE
Then hit [F.FWD/ B].
	– –	: – –	– –
4 Select the day	– MANUAL CLOCK SET –
Press [PLAY/K] or [STOP/L]	MONTH DAY		YEAR
until your desired day appears.	0 5	/ 0 5 – – – – – – –
(Example: 5th → “05”)	HOUR	MINUTE
Then hit [F.FWD/ B].	– –	: – –	– –
5 Select the year	– MANUAL CLOCK SET –
Press [PLAY/K] or [STOP/L]	MONTH DAY		YEAR
until your desired year appears.	0 5	/ 0 5	THU 2 0 0 5
(Example: “2005”)	HOUR	MINUTE
Then hit [F.FWD/ B].	– –	: – –	– –

- 13 - EN