Channel SET UP, Deleting or Adding Channel

CHANNEL SET UP

You can program the tuner to scan all the channels you receive in your area.

NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just select the TV/VCR channel selector to the

DELETING (OR ADDING)

CHANNEL

The channels you no longer receive or seldom watch can be deleted from the memory. (Of course, you can add the deleted channel into the memory again.)

output channel of the cable box or satellite box (Ex CH3). Then select the channel to be viewed on the Cable Box or Satellite Box.

Make sure ...

•Press the POWER button to turn on the TV/VCR.

1Select “CHANNEL SET UP”

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L but- ton to point to “CHANNEL SET UP”.

– M E N U –

TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK

BCHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN

TIME SEARCH INDEX SEARCH

Then, press the F.FWD/B button.

1Select “CHANNEL SET UP”

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L but- ton to point to “CHANNEL SET UP”.

Then, press the F.FWD/B button.

– M E N U –

TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK

BCHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN

TIME SEARCH INDEX SEARCH

2 Select “ADD/DELETE CH”	– CHANNEL SET UP –
Press the PLAY/K or STOP/L but-	B ADD / DELETE CH (CATV)
ton to point to “ADD/DELETE	AUTO CH PROGRAMMING
CH”.
Press the F.FWD/B button.

2Begin auto preset

Press the PLAY/K or STOP/L but- ton to point to “AUTO CH PRO- GRAMMING”.

Then, press the F.FWD/B button. The tuner scans and memorizes all the active channels in your area.

– CHANNEL SET UP –

ADD / DELETE CH (CATV)

BAUTO CH PROGRAMMING

3Enter the desired channel number

Press the PLAY/K or STOP/L but- ton until your desired channel num-

	ber appears. (You can also use the	08
	number buttons or the CHANNEL	ADD / DELETE
	K/L button to enter it) (Example:	ADD / DELETE
	K/L button to enter it) (Example:
	CH8)

• When selecting cable channels which are higher

than 99, press the +100 button first, then, press the

last two digits. (Example: to select channel 125,

3After scanning

The tuner stops on the lowest memorized channel.

•When AUTO CH PROGRAMMING is activated where there is no TV signal input, “NO TV SIG- NALS” will appear on the display after the com- pletion of the channel scanning.

•The TV/VCR may display TV channels to be CATV channels caused by poor antenna reception. In this case, try auto preset again.

first press the +100 button then press “2” and “5”).

• You must proceed single-digit channel numbers

with a zero (Example: 02 ... 09).

4Delete (or add) it from (into) memory

Press the F.FWD/B or REW/s button. The channel number changes to light red. The channel is deleted from memory.

•To delete another channel, repeat steps [3] and [4].

•If you press the F.FWD/B or REW/s button again, the channel is memorized again.

Added channel: Light blue.

Deleted channel: Light red.

5Exit the channel setup mode

Press the MENU button on the remote control to returns to TV mode.

NOTE: To confirm that channel(s) has been deleted or added, press the CHANNEL K or L button.

- 13 -

Sylvania SRC2213W, SRC2419 owner manual Channel SET UP, Deleting or Adding Channel