Magnavox CCX133AT99 warranty Timer Recording cont’d

Page 33

Timer Recording (cont’d) 33

4

Use the Number buttons (1 - 8) to select a position in which to store the timer recording. Flashing numbers indi- cate an open position (one in which a timer recording has not yet been stored).

NOTE: If you select a number that has already been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on-screen for a few seconds. Then information about the program in that position will appear on-screen. If this happens, press the STATUS/EXIT button. Then use the Number buttons to select another position.

5

●Enter the channel of the TV program you want to record (you must enter a 0 before all single digit channels).

●If you are recording from line input, press 0, 0. A/V IN will appear on-screen.

●If you are recording using a Cable Box,enter the Cable Box out- put channel (03 or 04). Be sure to select the channel at the Cable Box and leave the Cable Box on for the timer recording.

ONE TIME PROGRAM

PROGRAM 1

CHANNEL – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

6

Press two Number buttons for the hour(s) you want the recording to begin. Press two Number buttons for the minute(s) you want the recording to begin. Press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.

ONE TIME PROGRAM

PROGRAM 1

CHANNEL	10
TIME ON	– – : – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

7

Follow the instructions in step 6 to set the recording’s stop time. (AM or PM will be set automatically.)

ONE TIME PROGRAM

PROGRAM 1

CHANNEL	10
TIME ON	09:30 PM
TIME OFF	– – : – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

4-7

POWER			SLEEP
	2	3	ALT.CH
1	2	3
4	5	6	o
			CHANNEL
7	8	9	p
	0	+100	o
SPEED		MUTE	VOLUME
			p
	o
	PLAY
– REW			F.FWD +
	STOP
	p
REC/OTR	MEMORY	PAUSE/STILL VCR PLUS+
MENU	STATUS/EXIT	CLEAR	SMART
MENU	STATUS/EXIT	CLEAR	SOUND

Helpful Hints

•If the numbers entered do not match the TV/VCR’s internal calen- dar, the entry will be rejected and a question mark (?) will appear on the TV/VCR screen.

•To make corrections while you are programming a timer recording, press the CLEAR button until the cursor is flashing on the item you want to change. Then enter the cor- rect information.

Image 33

Contents CCX133AT For Customer Use Dear Philips Magnavox product ownerFeatures Safety PrecautionsIntroduction Table of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR Maintenance Removing the Shipping CardHook up your TV/VCR using one of the connections shown Hooking Up The TV/VCRRod Antenna Bent pin Hooking Up The TV/VCR cont’dCrooked Pin Straight Pin Cable PlugTurning On the TV/VCR Press the Menu button to display the pop up menu Language SelectionChannel Memory Press the Number 3 button to select ADD/DELETE Channel Adding/Deleting ChannelsEnter the channel number you want to add or delete Press the Menu buttonManual Clock Setting Setting the ClockChannels are programmed. Details are on pages 10 Press the Number 6 button to select SET ClockPress the Number 2 button to select SET Manual Clock Setting the Clock cont’dSetting the Clock cont’d Automatic PBS Channel SelectionPress the Menu button to display the pop up menu Wait for the TV/VCR to find TimePress the Number 1 button to select SET PBS CH Manual PBS Channel Selection Find the time Use the Number buttons to select your PBS stationNOW Searching flashes on the TV/VCR screen Press the PLAY/ button or the STOP/ button to select Daylight-Saving TimeTime Zone Press the Number 4 button to select SET Time ZoneYou cannot select Time Zone at if Auto Clock is set to OFF Front Panel ANTenna Jack Rear PanelConnect your antenna or cable here Details are on pages six sevenRemote Control Buttons ALT. CH Alternate Channel Button Volume Up/Down ButtonsChannel Up/Down Buttons Mute ButtonAdjusting the Picture Controls Decrease Increase Decreased brightnessPress the REWind/- button to decrease a picture control On-Screen Status Displays On ModeReminder Playing Speed are given below RecordingPress the RECord/OTR button once to start recording Recording options are on pages 30One Touch Recording OTRYou can not pause an OTR Rerecording Tape Duplication Different brands of equipment may operate differentlyAudio and video cables are not included Select a once, daily or weekly recording Timer RecordingTimer Recording cont’d Timer Recording cont’d Checking or Clearing Timer Recordings Setting Up the VCR Plus+ Programming System TV Channels Cable ChannelsLocal TV Stations Call letters Examine the lists on Press the Number 5 button to select VCR PLUS+ REF. MAPPress the STATUS/EXIT button to exit Screen display shown below will appear Press the VCR PLUS+ button on the remote control. The onTimer Recording With the VCR Plus+ Programming System cont’d Record Defeat Record DefeatFollow the steps below to prevent accidental recording If the power fails, you might lose the sleep timer setting Setting the Sleep TimerExample Closed CaptioningMenu ScreenClosed Captioning cont’d Standard Closed CaptioningText Screen Volume Bar Volume Bar / Smart SoundTo turn Volume Bar On or Off Smart SoundRepeat Playback Insert a tape in the TV/VCR B Repeat PlaybackRepeat Playback cont’d Real Time Counter Memory Button to reset the real time counter to zeroAppear on-screen While the counter remains on-screen, press the ClearAutomatic Operation Features Forward and Reverse Searching SP/LP/SLP Playback OptionsSuper High Speed Searching LP/SLP Viewing a Still PictureGlossary SpecificationsHelpful Hints Helpful Hints cont’d Renewed Index Supplied Accessories