Magnavox CCX133AT99 warranty Press the VCR PLUS+ button on the remote control. The on

Page 38

38 Timer Recording With the VCR Plus+ Programming System

Follow the steps below to program a timer recording using the PlusCode programming numbers in your TV guide. Before you begin, make sure:

●The clock has been set. If not, CLOCK MUST BE SET appears.

● Channels are programmed.	3
● Channels are programmed.
● There is a tape in the TV/VCR (make sure the tape’s record tab
is intact and the tape is long enough to record the program).
● You have completed the steps on pages 36-37.

Complete each step within 60 seconds of completing the previous step. If you don’t, you may return to step 1.

1

POWER

1 2

4 5

78

0

SPEED

–REW

SLEEP

ALT.CH

3

6o

CHANNEL

9p

+100 o

MUTE

VOLUME

p

o

PLAY

F.FWD +

2

Press the VCR PLUS+ button on the remote control. The on-	STOP
screen display shown below will appear.	p
screen display shown below will appear.	REC/OTR MEMORY PAUSE/STILL VCR PLUS+
VCR PLUS+ PROGRAM	MENU STATUS/EXIT CLEAR	SOUND
		SMART

PLUS CODE : – – – – – – – –

1

TO END PRESS EXIT

2

Press the Number buttons to enter the PlusCode pro- gramming number of the program you wish to record (this number is different for every program, and it can be four to eight digits long). Finally, press the VCR PLUS+ button.

VCR PLUS+ PROGRAM

PLUS CODE : 60590 – – –

TO SET PRESS VCR +

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

3

To record the program once, press the Number 1 button to select ONCE. To record the same program every day from Monday through Friday, press the Number 2 button to select DAILY. To record the same program every week on the same day (such as every Saturday), press the Number 3 button to select WEEKLY.

VCR PLUS+ PROGRAM

1ONCE

2DAILY (MON - FRI)

3WEEKLY

TO SELECT PRESS NUMBER

TO END PRESS EXIT

Helpful Hints

•If the power fails, programmed timer recordings will be lost.

•You cannot set a timer recording if the TV/VCR is in Record Defeat mode. To set the Record Defeat mode to OFF, see page 40.

•If CODE ERROR flashes after you enter the PlusCode programming number and press the VCR PLUS+ button, the number you entered was incorrect (for example, too short). If this happens, enter the correct num- ber.

•CLASH may flash on the screen after you complete step 2. This means that the timer recording you just pro- grammed and another timer record- ing overlap, and thus the current timer recording will not be carried out.

Image 38

Contents CCX133AT Dear Philips Magnavox product owner For Customer UseIntroduction FeaturesSafety Precautions Table of Contents VCR Maintenance Putting Batteries in the Remote ControlUsing the Remote Control Removing the Shipping CardRod Antenna Hook up your TV/VCR using one of the connections shownHooking Up The TV/VCR Crooked Pin Straight Pin Hooking Up The TV/VCR cont’dBent pin Cable PlugTurning On the TV/VCR Language Selection Press the Menu button to display the pop up menuChannel Memory Enter the channel number you want to add or delete Adding/Deleting ChannelsPress the Number 3 button to select ADD/DELETE Channel Press the Menu buttonChannels are programmed. Details are on pages 10 Setting the ClockManual Clock Setting Press the Number 6 button to select SET ClockSetting the Clock cont’d Press the Number 2 button to select SET Manual ClockPress the Menu button to display the pop up menu Setting the Clock cont’dAutomatic PBS Channel Selection Press the Number 1 button to select SET PBS CH Wait for the TV/VCR to findTime Manual PBS Channel Selection NOW Searching flashes on the TV/VCR screen Find the timeUse the Number buttons to select your PBS station Daylight-Saving Time Press the PLAY/ button or the STOP/ button to selectYou cannot select Time Zone at if Auto Clock is set to OFF Time ZonePress the Number 4 button to select SET Time Zone Front Panel Connect your antenna or cable here Rear PanelANTenna Jack Details are on pages six sevenRemote Control Buttons Channel Up/Down Buttons Volume Up/Down ButtonsALT. CH Alternate Channel Button Mute ButtonAdjusting the Picture Controls Press the REWind/- button to decrease a picture control Decrease IncreaseDecreased brightness On Mode On-Screen Status DisplaysReminder Playing Press the RECord/OTR button once to start recording RecordingSpeed are given below Recording options are on pages 30You can not pause an OTR One Touch RecordingOTR Audio and video cables are not included Rerecording Tape DuplicationDifferent brands of equipment may operate differently Timer Recording Select a once, daily or weekly recordingTimer Recording cont’d Timer Recording cont’d Checking or Clearing Timer Recordings Local TV Stations Call letters Setting Up the VCR Plus+ Programming SystemTV Channels Cable Channels Press the STATUS/EXIT button to exit Examine the lists onPress the Number 5 button to select VCR PLUS+ REF. MAP Press the VCR PLUS+ button on the remote control. The on Screen display shown below will appearTimer Recording With the VCR Plus+ Programming System cont’d Follow the steps below to prevent accidental recording Record DefeatRecord Defeat Setting the Sleep Timer If the power fails, you might lose the sleep timer settingMenu Closed CaptioningExample ScreenText Screen Closed Captioning cont’dStandard Closed Captioning To turn Volume Bar On or Off Volume Bar / Smart SoundVolume Bar Smart SoundRepeat Playback B Repeat Playback Insert a tape in the TV/VCRRepeat Playback cont’d Appear on-screen Button to reset the real time counter to zeroReal Time Counter Memory While the counter remains on-screen, press the ClearAutomatic Operation Features Super High Speed Searching LP/SLP Playback OptionsForward and Reverse Searching SP/LP/SLP Viewing a Still PictureSpecifications GlossaryHelpful Hints Helpful Hints cont’d Renewed Index Supplied Accessories