Memorex MVT2137 owner manual Location of Controls, Front Rear, Description of Controls

Page 8

LOCATION OF CONTROLS

FRONT

REAR

20

1

VIDEO

AUDIO

OUT LINE1

2

3

4

5

6

7

16

17

18

19

 

 

Volume

 

 

 

Channel

Stop/

Phones

Power

 

Eject

Power Rec/Otr T-Rec

Rew Play F.Fwd Rec/Otr

Video – In – Audio

8

9

10

11

12

13

14

15

DESCRIPTION OF CONTROLS

FRONT:

1.Cassette Loading Slot - To insert or remove a video tape.

2.POWER Button - Press to turn the TV/VCR on or off.

3.STOP/EJECT Button - Press once to stop the tape in any mode. Press again to eject the tape.

4.F.FWD (Fast Forward) Button - In the Stop mode, this button rapidly winds the tape forward. In the Play mode, this button activates forward search.

5.POWER Indicator - Lights when the power is turned on.

6.REC/OTR Indicator - Lights when the TV/VCR is re- cording.

7.T-REC Indicator - This lights when the TIMER REC button is pressed.

8.PHONES Jack - Plug monaural headphones or an earphone with an 1/8" miniplug into one or both of these jacks for private listening. Two people can use these jacks at the same time.

9.VOLUME / Buttons - Press to raise or lower the volume of the sound.

10.CHANNEL / Buttons - Press to select a channel for viewing or recording.

11.REW (Rewind) Button - In the Stop mode, this button rapidly winds the tape backwards. In the Play

8 mode, this button activates reverse search.

12.PLAY Button - Press to play a prerecorded tape.

13.REC/OTR Button - Press once to start normal recording. Additional presses activate One-touch Timer Recording.

14.Remote Sensor - Signals from the Remote Control are received here.

15.Audio/Video In (LINE 2) Jacks - Audio and video signal cables from an external source can be connected here.

REAR:

16.VHF/UHF Antenna Jack - Connect the 75 ohm coaxial cable from the antenna or Cable TV service to this jack.

17.AUDIO/VIDEO OUT Jacks - Used to output audio and video signals to a TV, amplifier or VCR.

18.AUDIO/VIDEO IN (LINE 1) Jacks - Audio and video signal cables from an external source can be connected here.

19.AC Power Cord - Connect to a 120V, 60Hz outlet.

20.DC Input Jack - Connect the 12V DC car cord (supplied) here for DC operation.

5A3A901A E P02-11

8

3/18/02, 10:07 PM

Image 8
Contents TV/CATV Mode Selection Seleccion DE Modo DE TV/CATV AtencionCleaning AccessoriesRead Instructions Retain InstructionsPower Sources POWER-CORD ProtectionPower Lines VentilationDamage Requiring Service Replacement Parts Safety CheckWall or Ceiling Mounting HeatSafety Precautions Moisture Condensation Install the TV/VCR in Your CARWhen YOU Experience the Above CONDI- Tions Location and HandleImportant Notes FeaturesDriving Safety Table of Contents Location of Controls Front RearDescription of Controls Cassette Loading Slot To insert or remove a video tapeRemote Control Eject Button Press to eject the tapeRemote Control Power Sources Battery InstallationBattery Precautions Effective Distance of the Remote ControlAntenna Connections Replacing the Fuse in the CAR Cord PlugSetting the Language For Subscribers to Basic Cable TV ServiceFor Subscribers to Scrambled Cable TV Service Cable TV ConnectionsAuto Clock Setting Manual Clock Setting TV mode direct channel selectionCatv mode direct channel selection VHF/UHF/CATV ChannelsTV Operation TV/CATV Selection Automatic Memory TuningTV Operation To Memorize Channels To SET the V-CHIP To Memorize Channels Setting the V-CHIPTo ADD/DELETE Channels To SET the on Timer To Change PasswordDisplay on Menu screen is clearedTo SET the OFF Timer Picture Control AdjustmentsPlayback Special Playback ONE-TOUCH Timer Recording OTR Timer RecordingUsing the Real Time Tape Counter Using Zero ReturnConnection to Camcorder Duplicating a Video TapeConnection to Another VCR Video Head Cleaning Reception DisturbancesTroubleshooting Guide Symptom Cause Possible Solution PowerOperate Heads Two or three hours until it goes off TV Broadcast ReceptionSymptom Cause Possible Solution Remote ControlRecording PlaybackSpecifications AccessoriesTelevision VCRMemo