ELAN Home Systems Digital Music Server manual Configuring Your Remote to Control Other Devices

Page 12

E L A N H O M E S Y S T E M S

USER GUIDE

CONFIGURING YOUR REMOTE TO CONTROL OTHER DEVICES

The TV and Amp devices on the VIA!dj remote control may be individually configured to control a range of televisions and amplifiers from well known manufacturers.

To configure the remote to control your television:

Press the TV and buttons simultaneously; hold them down for 1 second.

The TV button will remain lit for 20 seconds; the configu- ration process must be completed during this time.

Enter the 3 digit numeric code matching the manufacturer of your television from the list in Appendix A, p. 26-30.

Press the TV button again.

The TV button will blink twice to indicate that the configuration has been accepted. If the TV button does not blink begin the process again, taking care to enter the number exactly as print- ed in the list. If the television is switched on during the config- uration process, entering the correct code will cause the televi- sion to go into standby.

To configure the remote to control your amplifier:

Press the Amp and buttons simultaneously; hold them down for 1 second.

The Amp button will remain lit for 20 seconds; the configuration process must be completed during this time.

Enter the 3 digit numeric code matching the manufacturer of your amplifier from the list in Appendix A.

Press the Amp button again.

The Amp button will blink twice to indicate that the configura- tion has been accepted. If the Amp button does not blink begin the process again, taking care to enter the number exactly as printed in the list. If the amplifier is switched on during the configuration process, entering the correct code will cause the amplifier to go into standby.

SWITCHING ON AND OFF

The VIA!dj was designed to remain on 24/7/365. If the VIA!dj is not going to be used for an extended period of time and you wish to turn it off, there are two power saving modes available from the Standby button on the VIA!dj front panel and the button on the remote control. The VIA! Touch Panel can be used to take the VIA!dj out of Standby, but it cannot be used to put the VIA!dj into Standby Mode.

STANDBY AND OFF MODES

Standby Mode

Putting the unit into standby takes just a few seconds; switch- ing the unit on from standby also takes just a few seconds. DO NOT remove the power cord from the VIA!dj in this mode.

Off Mode

Off mode should be used only if the VIA!dj is not being used for an extended period of time. There is a short wait while the unit is switched to off mode; switching the unit on from off mode may take a few minutes. You can safely remove the power from the VIA!dj in this mode.

To enter standby or off mode:

Press the Standby key on the front panel or the Standby key on the remote control.

The following screen is displayed:

The front panel display shows:

Either:

Press the Standby button on any VIA! Touch Panel, or the Stby action key on the front panel, or the key on the remote control to switch to standby.

After a short delay the screen shows:

Or:

Press the Off button on any VIA! Touch Panel, or the Off action key on the front panel, or the key on the remote control to switch to off mode.

After a short period of time the display and front panel display will switch off.

To switch on from standby or off mode:

Press the Standby button on any VIA! Touch Panel, or press the Standby key on the front panel, or the Standby key on the remote control.

© ELAN Home Systems 2004 • All rights reserved. 02/04

Page 11

Image 12
Contents Users Guide Table of Contents Precautions General PrecautionsCD Handling Precautions Copyright NoticeImportant Safety Instructions Copyright NoticeStandby Button Important Safety Notices ModelInformation to User Canadian ModelIntroduction Specifications Controls and Connections Front PanelRear Panel Remote Control Navigation Configuring Your Remote to Control Other Devices Switching on and OFFStandby and OFF Modes Using the VIA!DJ Front Panel Action Keys VIA!DJ ScreenTo Register Your VIA!DJ VIA!DJ Status IconsTo USE the Alphanumeric Keypad To Connect Your VIA!DJ to InternetAction HOWRecording Music Press RegisterTo select an option from the main menu VIA!dj can not recordRecording from a CD To make an automatic one-touch CD recordingTo Make a Custom CD Recording Recording QualityCD File TimePlaying Music CD-TEXT SupportListening to Music While Recording a CD Playing Music from the LibraryOption DescriptionSelecting Items Directly Using Your VIA!DJ Remote Control Playing Music from a CD Output ScreenTo play a disc VIA!dj AudioOrganizing Your Music Collection Controlling PlaybackPlaylists Music from the Library p.18-19 To select items for a playlistEditing a Playlist To add items to a playlistAlbum Information To remove a track from a playlistTo change the position of a track within a playlist Deleting albums, tracks or playlistsAdvanced Settings To Display the Settings MenuRegistration Details Internet AccountDefault Recording Quality System SettingsDedicated Remote Control USE in a Multiroom System Terms and ConditionsService Getting HelpOther Multiroom Control Systems Your DealerCondor Interfunk Philipsf AMP ThornNEW Features Recording from AN Analog or Digital InputLINE-IN Source Monitor OutputTo record from the line-in connectors To adjust the recording gain setting for the Analog InputTo edit the album details To edit the album name and artist nameQuick ADD Presets Storing a PresetTo select the music for a preset Limited Warranty