ELAN Home Systems Digital Music Server Terms and Conditions, Default Recording Quality, Language

Page 26

E L A N H O M E S Y S T E M S

USER GUIDE

TERMS AND CONDITIONS

Displays the terms and conditions of the XIVA Customer Service Agreement.

• Press ✔Cont. to return to the Settings menu.

DEFAULT RECORDING QUALITY

Allows you to specify the recording quality used when you record music using the Auto record option:

For each quality setting the screen shows the number of hours of recording time available at that setting.

OPTION

Internet Access

Modem Settings

Ethernet Settings

Controller Settings

Video Settings

Remote Diagnostics

DESCRIPTION

Specifies whether your VIA!dj connects to the Internet via the built-in modem or using the Ethernet port.

Allows you to specify the following settings when connecting via the built-in modem: number of connec- tion retries, the Assigned IP address and the Sever IP address, the modem initialization string, and whether to use tone or pulse dialing.

Allows you to specify the following settings when connecting via the Ethernet port: IP address mode, IP address, IP Mask, Gateway, IP DNS1, IP DNS2.

Specifies the communication speed for the Controller port on the rear of the unit.

Specifies whether the unit is config- ured for NTSC or PAL use.

Select this option if instructed to set up your modem to receive incoming calls from ELAN technical support

staff.

LANGUAGE

Allows you to select the language for the TV user interface— languages available are English, French, German, Italian, and Spanish.

SYSTEM INFORMATION

Shows the serial number, production date, and software version number of your VIA!dj. You may need to quote these if you contact ELAN for technical support.

SYSTEM SETTINGS

Provides a series of menus to allow you to change the hardware configuration on your VIA!dj:

The table in the next column summarizes the settings available on each of the System Settings menus:

DEDICATED REMOTE CONTROL USE IN A MULTIROOM SYSTEM

In rooms that have TVs with VIA!dj graphics available, but do not have VIA! Touch Panels, you may wish to have a dedicated VIA!dj remote control for that specific room. Your VIA!dj remote control can be configured so that every button press indicates to the VIA!dj which output is to be controlled. This means that whenever infra-red is received by the VIA!dj the VIA! Touch Panel and/or TV display will automatically switch to controlling the appropriate output.

To configure the remote with a default output

•Press the HDD Audio and k buttons simultaneously; hold them down for 1 second.

The HDD Audio button will remain lit for 20 seconds; the configuration process must be completed during this time.

•Enter the 3 digit code corresponding the output you would like to control (valid configurations are listed in Appendix A). For example, to set output 2 as your default output press: 0, 0, 2

•Press the HDD Audio button again.

The HDD Audio button will blink twice to indicate that the configuration has been accepted. If the HDD Audio button does not blink twice begin the process again, taking care to enter the number correctly.

If the VIA!dj is switched on during the configuration process the Enter Standby? prompt will appear once configuration is complete. Press ✖Cancel to return to the previous screen.

Now, pressing any navigation key on the remote should cause the VIA!dj to switch to the correct output. To return the remote control to factory default Output select operation:

•Follow the above procedure and enter 0, 0, 0 as the 3-digit code.

© ELAN Home Systems 2004 • All rights reserved. 02/04

Page 25

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Users Guide Table of Contents CD Handling Precautions PrecautionsGeneral Precautions Copyright NoticeStandby Button Important Safety InstructionsCopyright Notice Information to User Important Safety NoticesModel Canadian ModelIntroduction Specifications Controls and Connections Front PanelRear Panel Remote Control Navigation Standby and OFF Modes Configuring Your Remote to Control Other DevicesSwitching on and OFF To Register Your VIA!DJ Using the VIA!DJ Front Panel Action KeysVIA!DJ Screen VIA!DJ Status IconsAction To USE the Alphanumeric KeypadTo Connect Your VIA!DJ to Internet HOWTo select an option from the main menu Recording MusicPress Register VIA!dj can not recordRecording from a CD To make an automatic one-touch CD recordingCD File To Make a Custom CD RecordingRecording Quality TimeListening to Music While Recording a CD Playing MusicCD-TEXT Support Playing Music from the LibraryOption DescriptionSelecting Items Directly Using Your VIA!DJ Remote Control To play a disc Playing Music from a CDOutput Screen VIA!dj AudioPlaylists Organizing Your Music CollectionControlling Playback Editing a Playlist Music from the Library p.18-19To select items for a playlist To add items to a playlistTo change the position of a track within a playlist Album InformationTo remove a track from a playlist Deleting albums, tracks or playlistsRegistration Details Advanced SettingsTo Display the Settings Menu Internet AccountDedicated Remote Control USE in a Multiroom System Default Recording QualitySystem Settings Terms and ConditionsOther Multiroom Control Systems ServiceGetting Help Your DealerCondor Interfunk Philipsf AMP ThornLINE-IN Source NEW FeaturesRecording from AN Analog or Digital Input Monitor OutputTo edit the album details To record from the line-in connectorsTo adjust the recording gain setting for the Analog Input To edit the album name and artist nameQuick ADD To select the music for a preset PresetsStoring a Preset Limited Warranty
Top Page Image Contents