Nuvo NV-LRC1 manual Using Learning, Press and hold Setup until the LED blinks twice

Page 6

Now, when you press the Macro key, the remote will send the series of commands you have entered, but only if you are in the mode you selected in step 1. For example, you could program the Macro key to turn on your T2 tuner and select a particular channel, but only if you are in tuner mode. If you are in DVD mode, this key will do nothing.

Clearing a Mode-Dependent Macro

1.Press and hold SETUP until the red LED blinks twice, then release.

2.Press 978.

3.Press the source key where you programmed the macro (Source 1-6).

4.Press the macro’s activation key (POWER, any unused key, etc.).

5.Press and hold SETUP until the red LED blinks twice, then release.

Using Learning

The NV-LRC1 includes a Learning feature so you can add functions that are unique to your home entertainment devices (e.g., CD skip forward or backward). However, there are some considerations:

Learning Precautions

-Your original remote controls must be in working order for learning to work properly.

-Learning keys are mode specific, so each one can store a unique function for each mode.

-Learned keys can be used in macros (See Using Macros).

-Do not use the following keys for learning: Source Keys, SETUP, BACK,

REPEAT, FAV SCAN, SLEEP, or Record () Key.

-Learning capacity is approximately 16 to 25 keys, depending on the code being learned.

-Certain device codes are not learnable including multi-frequency types, some high frequency ones, and other unusual formats.

-For optimum learning: avoid high levels of ambient light such as natural sunlight or energy-efficient fluorescent lights.

NOTE: Please have your original remote controls handy before programming learning.

Programming a Learned Key

NOTE: If more than 10 seconds pass between key presses, the remote exits programming.

1.Press and hold SETUP until LED flashes twice.

2.Press 975.

3.Press a source key once (1-6) to assign a mode for learning.

4.Place the NV-LRC1 head-to-head (about 2” apart) from your original remote control. Also locate the key (on your original remote control) that will serve as the teaching function.

VOL -

V O L +

ON/OFF

41

5 2

63

2"

5.On the NV-LRC1, press a key where the learned function will be stored.

6.On the original remote, press and hold the key to be learned. The LRC1’s LED will turn off. Continue holding the key on the original remote until the LRC1’s LED blinks twice.

NOTE: If the LED displays one long blink, a learning error has occurred. Try repeating this step again until a successful capture occurs. If the function is still not captured, press and hold SETUP to exit programming and review the “Learning Precautions” above. If needed, also see “Troubleshooting”. After review, start programming again at step1.

7.Repeat steps 2 to 6 for another key or press and hold SETUP to exit programming.

Deleting a Single Learning Key

1. Press and hold SETUP until the LED flashes twice.

NOTE: If more than 10 seconds pass between key presses, the remote exits programming.

2.Press SETUP, then 976 to delete a learned function.

3.Press a source key once (1-6).

4.Press the key containing the learned function to be deleted. The remote blinks twice.

5.Repeat steps 2 to 4 for another key or press and hold SETUP to exit programming.

Deleting All Learned Keys in a Specific Mode

1. Press and hold SETUP until the LED blinks twice.

NOTE: If more than 10 seconds pass between key presses, the remote exits programming.

2.Press 976.

3.Press a source key twice (1-6)to clear all the learned keys for that Mode. The LED blinks twice.

4.Repeat step 3 for another key or press and hold SETUP to exit Programming.

4

Image 6
Contents NV-LRC1 Page Installing Batteries IntroductionQuick Look At The Controls Whole-Home Control Programming a DeviceSearching For Your Code To control devices, 1-6, follow these stepsProgramming Macros Changing Volume LockChecking The Codes Enter 990. The LED blinks twiceUsing Learning Press and hold Setup until the LED blinks twicePress Problem CH+,CH-, and Last do not work for your RCA TV TroubleshootingProblem LED does not blink when you press a key Control for NuVo T2 TunerSetup Codes for Audio Amplifiers Setup Codes for Audio Amp/TunersKLH GPXJBL LXIGMI Setup Codes for Cable ConvertersABC NSCSetup Codes for CD Players Setup Codes for DVD Players SVA TYTSetup Codes for TVs Setup Codes for Satellite ReceiversCXC ECEKLL JCBKEC KTVNTC SSS TMKTVS CCE Setup Codes for VCRsABS HI-QKodak 20035 Kolin 20043 20384Kenwood 20067, 20041, 20038 21037Setup Codes for Video Accessories SMCSpecifications CareFCC Notice Page Arbor Tech Dr Hebron, KY