SUPER MICRO Computer sc827 user manual

Page 34

SC827 Chassis Manual

8.Connect the cables between the motherboard, backplane, chassis, front panel, and power supply, as needed. Also, fans may be temporarily removed to allow access to the backplane ports.

9.Replace the add-on card bracket and secure the bracket with a screw.

10.Repeat steps 3 - 5 for the remaining nodes.

5-12

Image 34

Contents Super SC827 Chassis Manual Preface About This ManualManual Organization IntroductionCompatible Backplanes Table of Contents Rack Installation Viii Shipping List Chapter IntroductionOverview Part NumbersContacting Supermicro Returning Merchandise for Service SC827 Chassis Manual Preparing for Setup Chapter System SafetyElectrical Safety Precautions Page System Safety Page Chapter Chassis Components ComponentsWhere to get Replacement Components Power SupplyChapter System Interface Chassis Control PanelControl Panel Buttons Control Panel LEDsDrive Carrier LEDs SAS/SATA DrivesSC827 Chassis Manual Chapter Chassis Setup and Maintenance Remove two Screws Check Ventilation Openings Chassis CoverRemoving the Chassis Cover and Protective Film Installing and Removing Hard Drives Motherboard Drawer Locations in the ChassisRemoving a Hard Drive Tray Removing Hard Drive Trays from the ChassisInstalling a Drive into the Hard Drive Tray Dummy Drive Drive TraySAS or Sata Hard Drive Drive Tray Removing Hard DriveRemoving the Backplane Removing and Installing the BackplaneRemoving the Backplane from the Chassis Loosening the Spring Bar Screws in the Floor of the Chassis Installing the Backplane Installing the Backplane into the ChassisCompatible Motherboards Permanent and Optional Standoffs Installing the MotherboardShields Chassis Setup and Maintenance Page Adapter Card Motherboard Drawer Spacer Plate Five Screws Installing and Replacing Adapter CardsInstalling the Adapter Card Removing the Adapter CardAdd-on Card/Expansion Slot Setup Add-on Card Slot Clip PCI Slot ShieldInstalling the Riser Card Installing the Riser CardAdd-on Card Installing Add-on CardsRiser Card Installing an Air Shroud Installing the Air ShroudsAir Shrouds Checking the Airflow Installation CompleteChecking Airflow Optional Fan Configurations System Fans18 System Fan Placement Changing a System FanPower Supply Replacement Power SupplyRelease Tab Changing the Power Supply Choosing a Setup Location Chapter Rack InstallationUnpacking the System Rack Precautions General Server PrecautionsRack Mounting Considerations Rack Mounting Instructions Identifying the Sections of the Rack RailsReleasing the Inner Rail Locking TabsReleasing Inner Rail from the Outer Rails Installing the Inner Rails Installing The Inner Rails on the ChassisInner Rails Installing the Outer Rails on the Rack Installing the Outer RailsInstalling the Chassis into a Rack Standard Chassis InstallationBall-Bearing Shuttle Optional Quick Installation Method SC827 Chassis Manual Appendix a Cables, Screws Other Accessories Overview Compatibility and Optional Accessories ListChassis Screws DVD-ROM, CD-ROM, and Floppy DriveAppendix B SC827 Power Supply Specifications SC827 Chassis Manual ESD Safety Guidelines Appendix C SAS-827T Safety GuidelinesGeneral Safety Guidelines An Important Note to Users Introduction to the SAS-827T BackplaneFront Connectors and Jumpers Connector, Jumper and Pin DefinitionsFront Connectors MB Power Connections Connector Motherboard Front Connector and Pin DefinitionsMotherboard Power Connectors SAS PortsSystem Fans FAN4 FAN3 Chassis Fan ConnectorsFan Connector Y-Cable Optional feature, sold separately SAS-827T BackplaneManufacturers Test Connectors Backplane Main Power ConnectorsUpgrade Connector 14. 15. Backplane to Front Panel Headers22. 33. SAS Ports Figure C-7 Motherboard Locations In the ChassisFront Jumper Locations and Pin Definitions Explanation of JumpersState Specification Front LED IndicatorsD11 Rear Connectors and LED Indicators Appendix D SAS-827B Backplane Specifications Introduction to the SAS-827B Backplane Front Connectors Jumpers and Pin DefinitionsSAS-827B Backplane Motherboard to Backplane Connec- tors13. 14. Backplane to Front Panel Headers To modify the operation of the backplane Means the jumper is on and Open meansLED Indicators StateD13 D14J11 D18 D24 D27 Figure D-6 Motherboard Locations In the Chassis