SUPER MICRO Computer sc827 Installing and Replacing Adapter Cards, Removing the Adapter Card

Page 35

Chapter 5: Chassis Setup and Maintenance

5-6 Installing and Replacing Adapter Cards

Adapter cards provide hot-swappable functionality to the chassis.

Adapter Card

Motherboard

Drawer

Spacer Plate

Five Screws

Figure 5-13: Adapter Card Installation

Removing the Adapter Card

1.Remove the motherboard drawer from the chassis.

2.Disconnect the wiring, connecting the adapter card to the motherboard if any is present.

3.Remove the five screws securing the adapter card and the spacer plate to the drawer and set them aside for later use.

4.Remove the adapter card and spacer plate from the motherboard drawer.

5.Set the spacer plate aside for later use.

Installing the Adapter Card

1.Make sure the motherboard has been installed properly in the node drawer before installing the adapter card

2.Place the adapter card and spacer plate in the motherboard drawer, aligning the holes in the spacer and the adapter card with the holes in the mother- board drawer.

3.Secure the adapter card and spacer plate to the motherboard drawer, using the five M3 flathead screws which were previously set aside.

4.Reconnect the wiring from the motherboard to the adapter card if necessary.

5.Return the motherboard drawer to the closed position in the chassis.

5-13

Image 35
Contents Super SC827 Chassis Manual About This Manual PrefaceIntroduction Manual OrganizationCompatible Backplanes Table of Contents Rack Installation Viii Part Numbers Chapter IntroductionOverview Shipping ListContacting Supermicro Returning Merchandise for Service SC827 Chassis Manual Electrical Safety Precautions Chapter System SafetyPreparing for Setup Page System Safety Page Components Chapter Chassis ComponentsPower Supply Where to get Replacement ComponentsChassis Control Panel Chapter System InterfaceControl Panel LEDs Control Panel ButtonsSAS/SATA Drives Drive Carrier LEDsSC827 Chassis Manual Chapter Chassis Setup and Maintenance Removing the Chassis Cover and Protective Film Chassis CoverRemove two Screws Check Ventilation Openings Motherboard Drawer Locations in the Chassis Installing and Removing Hard DrivesRemoving Hard Drive Trays from the Chassis Removing a Hard Drive TrayDummy Drive Drive Tray Installing a Drive into the Hard Drive TrayRemoving Hard Drive SAS or Sata Hard Drive Drive TrayRemoving the Backplane from the Chassis Removing and Installing the BackplaneRemoving the Backplane Loosening the Spring Bar Screws in the Floor of the Chassis Installing the Backplane into the Chassis Installing the BackplaneShields Installing the MotherboardCompatible Motherboards Permanent and Optional Standoffs Chassis Setup and Maintenance Page Removing the Adapter Card Installing and Replacing Adapter CardsInstalling the Adapter Card Adapter Card Motherboard Drawer Spacer Plate Five ScrewsAdd-on Card Slot Clip PCI Slot Shield Add-on Card/Expansion Slot SetupInstalling the Riser Card Installing the Riser CardRiser Card Installing Add-on CardsAdd-on Card Air Shrouds Installing the Air ShroudsInstalling an Air Shroud Checking Airflow Installation CompleteChecking the Airflow System Fans Optional Fan ConfigurationsChanging a System Fan 18 System Fan PlacementRelease Tab Power SupplyPower Supply Replacement Changing the Power Supply Unpacking the System Chapter Rack InstallationChoosing a Setup Location General Server Precautions Rack PrecautionsRack Mounting Considerations Identifying the Sections of the Rack Rails Rack Mounting InstructionsReleasing Inner Rail from the Outer Rails Locking TabsReleasing the Inner Rail Inner Rails Installing The Inner Rails on the ChassisInstalling the Inner Rails Installing the Outer Rails Installing the Outer Rails on the RackBall-Bearing Shuttle Standard Chassis InstallationInstalling the Chassis into a Rack Optional Quick Installation Method SC827 Chassis Manual Overview Compatibility and Optional Accessories List Appendix a Cables, Screws Other AccessoriesDVD-ROM, CD-ROM, and Floppy Drive Chassis ScrewsAppendix B SC827 Power Supply Specifications SC827 Chassis Manual General Safety Guidelines Appendix C SAS-827T Safety GuidelinesESD Safety Guidelines Introduction to the SAS-827T Backplane An Important Note to UsersFront Connectors Connector, Jumper and Pin DefinitionsFront Connectors and Jumpers SAS Ports Front Connector and Pin DefinitionsMotherboard Power Connectors MB Power Connections Connector MotherboardSAS-827T Backplane Chassis Fan ConnectorsFan Connector Y-Cable Optional feature, sold separately System Fans FAN4 FAN314. 15. Backplane to Front Panel Headers Backplane Main Power ConnectorsUpgrade Connector Manufacturers Test ConnectorsFigure C-7 Motherboard Locations In the Chassis 22. 33. SAS PortsExplanation of Jumpers Front Jumper Locations and Pin DefinitionsD11 Front LED IndicatorsState Specification Rear Connectors and LED Indicators Appendix D SAS-827B Backplane Specifications Introduction to the SAS-827B Backplane Jumpers and Pin Definitions Front ConnectorsMotherboard to Backplane Connec- tors SAS-827B Backplane13. 14. Backplane to Front Panel Headers Means the jumper is on and Open means To modify the operation of the backplaneState LED IndicatorsJ11 D18 D24 D27 D14D13 Figure D-6 Motherboard Locations In the Chassis