Controlling a TV with the Remote
The remote control can be competible with various brands of TV by setting their control codes. The TOSHIBA code has initlally been set to control TOSHIBA TVs.
Setting Control Codes
1.Press TV to set the remote control operating your TV.
2.While holding down PROG button enter the two digits of your TV’s brand code (listed right) using number buttons.
3.Release PROG.
4.Point the remote control at your TV and use each button listed below to make sure your TV is operated correctly.
TV POWER | To turn the TV on or off. |
CH | To select TV channels in the |
| upper or lower direction. |
TV VOL. | To adjust the sound level. |
I.SELECT | To select an external source |
| such as a VCR. |
Number buttons | To select TV channels. |
| When selecting channels 1 to |
| 9, first enter 0 and then the |
| desired number. |
100To substitute for 100 channel key.
DISPLAY | To turn on or off TV’s screen |
| display. |
ENTER | To use for the TV’s ENTER |
| key. |
Important Note
•Some TV’s may not respond to all the operations above, or may not be operated at all with this remote control. In this case, operate your TV with its own remote control.
•For some brands, several control codes (brand codes) are allocated. Try each of them until the buttons work on your TV.
•If you replace the remote control’s batteries, set the brand code again.
Table of Brand Codes
BRAND | CODE |
TOSHIBA | PROG + 01 |
|
|
RCA/GE | PROG + 02 |
|
|
SONY | PROG + 03 |
MITSUBISHI | PROG + 04 |
|
|
JVC | PROG + 05 |
|
|
HITACHI | PROG + 06 |
|
|
PANASONIC A | PROG + 07 |
|
|
SHARP NEW | PROG + 08 |
SANYO | PROG + 09 |
MAGNAVOX | PROG + 10 |
GOLDSTAR NEW | PROG + 11 |
|
|
SAMSUNG | PROG + 12 |
|
|
SHARP OLD | PROG + 13 |
|
|
ZENITH | PROG + 14 |
|
|
PANASONIC B | PROG + 15 |
|
|
PIONEER | PROG + 16 |
|
|
Troubleshooting
Before requesting service (troubleshooting), please check the following.
Problem |
| Action | Page |
|
|
|
|
No operations can be | • | Check the batteries in the remote. They may need replacing. |
|
• | Operate the remote control within 30 angle on either side of the |
| |
performed with remote. |
| ||
| remote sensor, up to a distance of no more than 23 feet. |
| |
|
| P5 | |
| • | Remove batteries and hold down one or more buttons for several | |
|
| minutes to drain the microprocessor inside the remote to reset it. |
|
|
| Reinstall batteries and try to operate the remote again. |
|
Disc does not play. | • | Ensure that the disc is installed with the label side facing up. | P7 |
| • | Check the region number of the DVD. | |
|
| ||
5.1 channel sound is not | • | 5.1 channel sound is reproduced only when the following condi- |
|
being reproduced. |
| tions are met. : |
|
|
| 1) The DVD player is connected with the proper amplifier |
|
|
| 2) The disc is recorded with 5.1 channel sound. | P12 |
| • | Check whether the disc being played has the “Dolby 5.1 ch” mark | |
|
| ||
|
| on the outside. |
|
| • | Check if your audio system is connected and working properly. | P31~32 |
| • | In a SETUP Menu, is the Audio Output set to Bitstream? |
|
The | icon appears on | • The features or action cannot be completed at this time because: |
| |
screen. |
| 1. | The DVD’s software restricts it. |
|
|
| 2. | The DVD’s software doesn’t support the feature (e.g., angles). | P14 |
3.The feature is not available at the moment.
4.You’ve requested a title or chapter number or search time that is out of range.
Disc Menu doesn’t appear. | • | Check if the disc has a Menu. |
| |||||||||
Play mode differs from the | • | Some of the functions selected in the Setup Menu may not work | P29~35 | |||||||||
Setup Menu selection. |
| properly if the disc is not encoded with the corresponding function. | ||||||||||
|
| |||||||||||
The screen ratio cannot | • | The Screen Ratio is fixed on your DVD discs. | P33 | |||||||||
be changed. | ||||||||||||
|
|
|
|
|
|
|
|
|
|
| ||
No audio. | • | Make sure you have selected the correct Digital Output in the | P31~32 | |||||||||
| ||||||||||||
|
| Audio Options Menu. |
|
| ||||||||
The screen is blocked | • | Press power on from a cold start with no disc in the unit. Press the |
| |||||||||
|
| STOP ( |
|
| ) and PLAY ( |
|
|
| ) buttons simultaneously on the front | P14 | ||
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
| ||
|
| panel for three seconds. The SELECT MENU LANGUAGE display | ||||||||||
|
|
| ||||||||||
|
| will appear. Select the number button of the desired language. |
| |||||||||
Forgot password | • | Press power on from a cold start with no disc in the unit. Press the |
| |||||||||
|
| STOP ( |
|
|
| ) and PLAY ( |
|
| ) buttons simultaneously on the front |
| ||
|
|
|
|
|
|
|
| |||||
|
| panel for three seconds. |
| SELECT MENU LANGUAGE display |
| |||||||
|
| The | P34~35 | |||||||||
|
| will appear. Select the number button of the desired language. | ||||||||||
|
|
| ||||||||||
|
| Press the SETUP select Setup, then press RIGHT or ENTER. |
| |||||||||
|
| Press Up or Down to select Parental Setup. The Parental Setup is |
| |||||||||
|
| now unlocked as indicated on the display. You can change your |
| |||||||||
|
| password. |
|
|
|
|
|
| ||||
If you experience other | • | Go to the contents and find the section of the instruction book that |
| |||||||||
problems. |
| contains the explanations regarding the current problem, and follow |
| |||||||||
|
| the procedure once again. |
|
| ||||||||
| • | If the problem still cannot be solved, please contact your nearest |
| |||||||||
|
| authorized service center. |
|
| ||||||||
| ||
|
|
|