Toshiba HD-EP30KE, HD-EP30KB Connecting to a TV, Via Hdmi input, Via component video input

Page 15

Step 1: Connecting to a TV

•Connect the player directly to your TV. If you connect the player to a VTR, TV/VTR combination, video selector or AV amplifier, the playback picture may be distorted due to copy protection.

•Be sure to turn off the power and unplug both units from the wall outlet before making any connections.

Via HDMI input

To view 1080p output, make this connection.

HDMI transfers digital audio and uncompressed digital video on a single cable. As a result, audio cables and video cables don’t need to be connected separately to a device.

HDMI cable (supplied)

To HDMI OUTPUT

HDMI INPUT

 

 

 

 

 

TV

Depending on the TV connected, you can use the CEC function. For detail, see page 35.

Notes

•When the HDMI connection is not verified, an error message appears on the front panel display. In this case, disconnect the HDMI cable then connect it again, or turn off the connected HDMI device then turn it on.

•HDMI output is digital only, DVI analog is not supported.

•HDMI is an evolving technology, so it is possible that some devices may not operate properly with this player.

•To get the most possible benefit from Dolby Digital Plus, you should connect your HD DVD player to your AV receiver using its HDMI input. If your AV receiver has this type of input, make sure it is connected to your HD DVD player and that the input is set to use audio from HDMI (and not the SPDIF coaxial or optical input). If your AV receiver does not have an HDMI input, then the next best choice is to use the SPDIF (coaxial or optical) input on your AV receiver.

•If you use the SPDIF optical output or analog outputs to connect your audio system and have the “Digital Out HDMI” ( page 21) set to “Auto” or “PCM”, the audio output level from these jacks will be reduced when listening to a multichannel disc. To restore the audio output level, set “Digital Out HDMI” to “Downmixed PCM”.

Via component video input

Some discs may be down converted or require HDMI connection.

Not compatible with 1080p. To view 1080p output, select HDMI connection.

Component video cables (not supplied)

To COMPONENT

VIDEO OUTPUT

Y PB PR

TV

This connection only sends video signals. Be sure to make audio connection on page 16.

Via VIDEO (yellow) input

Composite video (yellow) cable (not supplied)

To VIDEO OUTPUT

480i/576i output only regardless of the resolution settings ( page 20) or the connections of other output jack.

This connection only sends video signals. Be sure to make audio

TV

connection on page 16.

Note

•This player supports simultaneous output of video on its HDMI and component video ports. However, some discs may restrict output of video on the component video ports when viewing high definition content or up-converted DVD content. The resolution on the HDMI output will be the same as the resolution output on the component video output. Thus, because the HDMI output can change automatically to match the maximum available resolution of your display, if you connect both the HDMI output and component output, the resolution on the component output will change if the HDMI output auto-adjusts.

15

HD-EP30KE_Eng.indd 15

07.9.3 2:01:43 PM

Page 14 Page 16
Image 15
Page 14 Page 16
Contents HD-EP30KB HD-EP30KE Result in hazardous radiation exposure This HD DVD player employs a Laser SystemFollowing information is only for EU-member states Location of the required labelImportant Safety Instructions Precautions Moisture condensation occurs during the following cases Do not use the unit when moisture condensation may occurTable of contents Features Disc compatibilityDisc Specification Customer support Important notes about HD DVDHD output jacks Certain system requirementsIndex to parts and controls Front panelRear panel Display Remote control Loading batteries AccessoriesRemote control Supplied accessoriesProceed the following steps to set the player ready Resolution and connectionsWhy Hdmi connection is most recommended? PreparationVia Video yellow input Connecting to a TVVia Hdmi input Via component video inputVia analog audio output Connecting to audio systemVia Hdmi output Via optical digital audio outputLAN connection Power connectionPowering on Setting up the playerLanguage Time Resolution Press / to select Picture, then press OKFor best viewing of film movie material 24p output Press / to select Audio, then press OK Audio outputEthernet To adjust the player’s clock via the network time protocolEnter the proxy server address when your provider Requires proxy settingNetwork Speed Cookie SettingPlaying Playing a discPlayback starts If playback does not start, press Play To change playback speed To pause playbackTo stop playback To resume playback from the location last stoppedDuring playback, press Subtitle To select subtitlesTo select the sound To select the camera angleTo locate a position To check the current statusTo play repeatedly Cursor controls Requirements for HD DVD discs/Web-enabled network contentHD DVD playing options in the future C/D buttonsADV Output sound conversion tableCustomizing the function settings During stop, press SetupGroup Setting Disc Details Picture SettingsLanguage AudioOn Screen Language How to select a languageSubtitle Language Audio LanguageGeneral EthernetUpdate Firmware Remote Controller SoundEnable Hdmi Maintenance InitializeSymptom Remedy Before calling service personnelSpecification Memo Memo Information on Customer Support
Top Page Image Contents