Toshiba HD-A3KC owner manual Connecting to a TV, Via Hdmi input, Via component video input

Page 15

Step 1: Connecting to a TV

•Connect the player directly to your TV. If you connect the player to a VCR, TV/VCR combination, video selector or AV amplifier, the playback picture may be distorted due to copy protection.

•Be sure to turn off the power and unplug both units from the wall outlet before making any connections.

Via HDMI input

HDMI transfers digital audio and uncompressed digital video on a single cable. As a result, audio cables and video cables don’t need to be connected separately to a device.

HDMI cable (not supplied)

To HDMI OUTPUT

HDMI INPUT

 

 

 

 

 

TV

Notes

•When the HDMI connection is not verified, an error message appears on the front panel display. In this case, disconnect the HDMI cable then connect it again, or turn off the connected HDMI device then turn it on.

•HDMI output is digital only, DVI analog is not supported.

•HDMI is an evolving technology, so it is possible that some devices may not operate properly with this player.

•To get the most possible benefit from Dolby Digital Plus, you should connect your HD DVD player to your AV receiver using its HDMI input. If your AV receiver has this type of input, make sure it is connected to your HD DVD player and that the input is set to use audio from HDMI (and not the SPDIF coaxial or optical input). If your AV receiver does not have an HDMI input, then the next best choice is to use the SPDIF (coaxial or optical) input on your AV receiver.

•If you use the SPDIF optical output or analog outputs to connect your audio system and have the “Digital Out HDMI” ( page 21) set to “Auto” or “PCM”, the audio output level from these jacks will be reduced when listening to a multichannel disc. To restore the audio output level, set “Digital Out HDMI” to “Downmixed PCM”.

Via component video input

Some discs may be down converted or require HDMI connection.

Component video cables (not supplied)

To COMPONENT

VIDEO OUTPUT

Y PB PR

TV

This connection only sends video signals. Be sure to make audio connection on page 16.

Via VIDEO (yellow) input

Composite video (yellow) cable (not supplied)

To VIDEO OUTPUT

TV

480i output only regardless of the resolution settings ( page 20) or the connections of other output jack.

This connection only sends video signals. Be sure to make audio connection on page 16.

Note

•This player supports simultaneous output of video on its HDMI and component video ports. However, some discs may restrict output of video on the component video ports when viewing high definition content or up-converted DVD content. The resolution on the HDMI output will be the same as the resolution output on the component video output. Thus, because the HDMI output can change automatically to match the maximum available resolution of your display, if you connect both the HDMI output and component output, the resolution on the component output will change if the HDMI output auto-adjusts.

15

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

Page 14 Page 16
Image 15
Page 14 Page 16
Contents HD-A3KU HD-A3KC Procedure This HD DVD player employs a Laser SystemResult in hazardous radiation exposure Location of the required label Important Safety Instructions Precautions Do not use the unit when moisture condensation may occur Moisture condensation occurs during the following casesWait Table of contents Features Disc compatibilityDisc Specification Customer support Important notes about HD DVDHD output jacks Certain system requirementsIndex to parts and controls Front panelRear panel Display Remote control Loading batteries AccessoriesRemote control Supplied accessoriesProceed the following steps to set the player ready Resolution and connectionsWhy Hdmi connection is most recommended? PreparationVia Video yellow input Connecting to a TVVia Hdmi input Via component video inputVia analog audio output Connecting to audio systemVia Hdmi output Via optical digital audio outputWith integrated router Power connectionLAN connection Connect eitherPowering on Setting up the playerLanguage If the time is correct, select OK by TimePress / to select Clock Set, then press Confirm the time is correctBelow, then press OK ResolutionPress To select Resolution Setting, then press OK Press To select Picture, then press OKPress / to select Audio, then press OK Audio outputEthernet Press To select Ethernet, then press OKTo select each of the followings, then press OK Select Other and press OK button Cookie SettingNetwork Speed Select the speed and press OK buttonPlaying Playing a discPlayback starts If playback does not start, press Play To change playback speed To pause playbackTo stop playback To resume playback from the location last stoppedDuring playback, press Subtitle To select subtitlesTo select the sound To select the camera angleTo locate a position To play repeatedlyTo check the current status Cursor controls Requirements for HD DVD discs/Web-enabled network contentHD DVD playing options in the future C/D buttonsOutput sound conversion table Group Setting Disc Details Customizing the function settingsDuring stop, press Setup Setup Menu appearsPicture SettingsLanguage AudioOn Screen Language How to select a languageSubtitle Language Audio LanguageGeneral EthernetUpdate Remote Controller Sound OffMaintenance Initialize Update FirmwareSymptom Remedy Before calling service personnelPre-installed software H i b i t a GNU General Public License Version 2, JunePreamble No Warranty H i b i t B END of Terms and ConditionsPage No Warranty H i b i t D H i b i t CSpecification Your Responsibility Limited One 1 Year Warranty on PartsRental Units Commercial UnitsHow to Obtain Warranty Services Your Responsibility Limited Canadian Warranty For Toshiba Brand HD DVD PlayersLimited Warranty for Commercial Units Rental UnitsArbitration and Dispute Resolution How to Obtain Warranty ServicesGeneral Provisions Information on Customer Support
Top Page Image Contents