Toshiba HD-A30KC owner manual Before calling service personnel, Symptom Remedy

Page 22

Before calling service personnel

Before accessing, try updating this player’s firmware. For details on how to update, see “Update (Firmware update)” ( page 35).

If you experience any of the following difficulties while using this unit, check the list below before consulting your nearest Toshiba dealer.

Symptom

Remedy

Page

 

 

 

 

No power.

Is the power plug disconnected? Check the power connection.

17

 

 

 

 

No picture.

Is the cable for connecting the player and TV disconnected or not connected properly?

15

 

 

Check the connections.

 

 

 

 

 

 

Switch the input of the connected TV to the signal from the player.

 

 

 

 

• Are both the HDMI OUTPUT jack and the COMPONENT VIDEO OUTPUT jacks

15

 

 

connected simultaneously? Select either connection and make the appropriate setting.

 

 

 

 

 

 

In case the menu of “Resolution Setting” disappears, make composite video (yellow)

20

 

 

connection to restore it, then select the resolution which is compatible with the connected

 

 

 

TV.

 

 

 

 

 

No sound.

Is the audio cable disconnected?

14, 16

 

 

 

 

 

Is the volume of the device turned down to the minimum level? Check the volume.

 

 

 

 

 

Switch the audio input of the device connected by the audio cable to the input from the

 

 

player.

 

 

 

 

 

 

Set “Digital Out SPDIF” or “Digital Out HDMI” properly in accordance with the connected

21

 

 

device and connection procedure.

 

 

 

 

 

 

Change the output resolution so that sound can be heard.

20

 

 

 

 

 

If using the optical digital output for a Dolby Digital Plus, Dolby TrueHD, DTS-HD or DTS

21

 

 

soundtrack, be sure your AV receiver or processor is set to use the input connected to

 

 

 

your player and is set to decode a DTS bitstream. If your AV receiver or processor does

 

 

 

not support DTS, select PCM output on the player.

 

 

 

 

 

The disc does not play.

Make sure the disc type can be played with the player.

8

 

 

 

 

 

Is the disc dirty or scratched? Check or clean the disc.

8

 

 

 

 

 

If the disc is a DVD-RW or DVD-R disc, finalize the disc before attempting to play it with

 

 

the player.

 

 

 

 

 

 

If the disc includes parent lock support, playback is restricted while the parent lock of the

34

 

 

player is set. Cancel Parental Lock or change the restriction level.

 

 

 

 

 

Playback picture has noise.

If video from the player is watched via a video recorder or on a TV with a built-in video

15

 

 

recorder, the copy guard may prevent images from being displayed properly. Be sure to

 

 

 

connect the player directly to the TV.

 

 

 

 

 

Playback picture does not

“Resolution Setting” > “up to 1080p/24Hz” is selected. Change the setting.

20

move smoothly.

 

 

 

The remote control does not

Are the batteries of the remote control dead? Replace the batteries.

13

work.

 

 

 

 

 

 

 

 

Make sure the remote control is within range and pointed in the correct direction.

13

 

 

 

 

HDMI Control (CE-Link) does

Make sure the HDMI cable is firmly connected, then turn on both the TV and the player

35

not work.

 

again.

 

Screen freezes and no buttons

Pressing ON/STANDBY button on the player for approximately ten seconds forces the

work.

 

player to turn off. Turn the player off and then on again.

 

 

 

 

 

After powering on, “Clock Set”

The power supply to the player may have been disconnected. Reset the clock.

19

menu appears.

 

 

 

36

HD-A30KUKC_Eng.indd 36

07.10.4 8:45:22 PM

Image 22
Contents HD-A30KU HD-A30KC Table of contents Certain system requirements Important notes about HD DVDHD output jacks Customer supportDisplay Preparation LanguageConfirm the time is correct TimePress / to select Clock Set, then press If the time is correct, select OK byPress To select Picture, then press OK ResolutionPress To select Resolution Setting, then press OK Below, then press OKAudio output Press / to select Audio, then press OKTo select each of the followings, then press OK EthernetPress To select Ethernet, then press OK NTP ServerPlaying Playback starts If playback does not start, press PlayTo resume playback from the location last stopped To pause playbackTo stop playback To change playback speedTo select the camera angle To select subtitlesTo select the sound During playback, press SubtitleTo play repeatedly To locate a positionTo check the current status Cursor controls Requirements for HD DVD discs/Web-enabled network contentC/D buttons Controller portOutput sound conversion table Setup Menu appears Customizing the function settingsDuring stop, press Setup Group Setting Disc DetailsPicture Audio LanguageSubtitle Language Language code listHow to select a language Audio LanguageEthernet To change the passwordTo change the limitation level of Parental Lock function GeneralMaintenance Initialize Remote Controller Sound OffEnable Hdmi Update FirmwareBefore calling service personnel Symptom RemedyGNU Lesser General Public License Version 2.1, February Specification Information on Customer Support