Toshiba RD-XV48KE owner manual Skip a Preset Channel, Move, To Select a Channel

6 Select “Channel” using [U \ D], then press [P].

7 Press [U \ D] to start scanning.

5 Select the position number you want to use using [the Number buttons] or [U \ D], then press [L].

E3LG0ED_EN.book Page 23 Wednesday, April 30, 2008 11:52 AM

3 Select “Manual Tuning” using [U \ D], then press [ENTER].

4 Select “Position” using [U \ D], then press [P].

Manual Tuning

Position	P02
Channel	1
Decoder	OFF
Skip	ON

•You can select position number 01 to 99.

•With [the Number buttons], you only need to enter the last 2-digit numbers.

•The tuner will begin to search up or down automatically. When a channel is found, the unit will stop searching and the picture will appear on the TV screen.

•You can select a desired channel number using [the Number buttons]. Refer to the following Channel Plan table and press the three digits to select the channel number.

(To select channel 4, press [0] first and then press [0] and [4]. Or press [4] and then “– – 4” appears and wait for 2 seconds.)

•If this is the channel you want, press [L].

Channel Plan

CH Indication		TV Channel
02	– 12	E2 - E12
13	– 20	A – H (only ITALY)
21	– 69	E21 – E69
74	– 78	X, Y, Z, Z+1, Z+2
80 – 99, 100		S1 – S20, GAP
121	– 141	S21 – S41
142	– 153	R1 – R12

This unit can receive the Hyper and Oscar frequency bands.

•If “Skip” is set to “ON”, select “Skip” using

[U \ D], then press [P]. Select “OFF” using

[U \ D], then press [L].

•If you want to decode scrambled signals, select “Decoder” using [U \ D], then press [P]. Select “ON” using [U \ D], then press [L].

•To store another channel, repeat steps 4 to 7.

8 Press [SETUP] to exit.

Skip a Preset Channel

You can set the unit to skip channels. You can no longer receive or watch when you access channels using [PROG. G \ H].

1	Follow steps 1 to 3 in “Manual	Introduction
2	Tuning” on pages 22 to 23.
	Select “Position” using [U \ D],
3	then press [P].
	Select the position number you want
	to skip using [the Number buttons]	Connections
4	or [U \ D], then press [L].
	Select “Skip” using [U \ D], then
5	press [P].
	Select “ON” using [U \ D], then
	press [L].
6	• To skip another channel, repeat steps 2 to 5.	Basic
	Press [SETUP] to exit.
		Setup
Move
You can replace two channels.
1	In stop mode, press [SETUP]. Select
		Recording
	“General Setting” using [U \ D],
2	then press [ENTER].
	Select “Channel” using [U \ D],
3	then press [ENTER].
	Select “Move” using [U \ D], then
4	press [ENTER].	Playback
	Select the position number that you
	wish to move the channel to using
	[U \ D], then press [ENTER].
	You cannot select a position number where
	“– – –”appears next to the number, because
	“Skip” is set to “ON” for that position number.
5	Move the channel to another	Editing
	position number using [U \ D], then
	press [ENTER].
6	• To move another channel, repeat steps 4 to 5.
	Press [SETUP] to exit.
		Function
To Select a Channel
You can select a channel using [PROG. G \ H], or		Setup
directly enter the channel using
[the Number buttons] on the remote control.
Notes on using [the Number buttons]:		VCR
• Enter channel numbers as a two-digit number for
the quickest result. For example, to select channel		Functions
6, press [0] and [6]. If you only press [6], channel 6
will be selected after 2 seconds. You can only select
channels 1 to 99.
		Others

EN 23