Toshiba 32HL17 Connecting an Hdmi or DVI device to the Hdmi input, To view the Hdmi device video

Page 17

Chapter 2: Connecting your TV

Connecting an HDMI™ or DVI device to the HDMI input

The HDMI input on your TV receives digital audio and uncompressed digital video from an HDMI source device, or uncompressed digital video from a DVI (Digital Visual Interface) source device.

This input is designed to accept HDCP (High-Bandwidth Digital-Content Protection) program material in digital form from EIA/CEA-861-D–compliant[1]consumer electronic devices (such as a set-top box or DVD player with HDMI or DVI output).

The HDMI input can accept and display VGA, 480i (60Hz), 480p (60Hz), 720p (60Hz), 1080i (60Hz), and 1080p (24Hz/ 60Hz) signal formats. For detailed signal specifications, see page 61.

Supported Audio format: Linear PCM, sampling rate 32/44.1/ 48 kHz

Note: To connect a PC to the HDMI input, see page 19.

To connect an HDMI device, you will need:

•one HDMI cable (type A connector) per HDMI device

–For proper operation, it is recommended that you use an

HDMI cable with the HDMI Logo ( ).

–To display an 1080p/60Hz signal format, you will need a Category 2 cable. Conventional HDMI/DVI cable may not work properly.

–HDMI cable transfers both video and audio. Separate analog audio cables are not required (see illustration).

–See “Setting the HDMI™ audio mode” (- page 32).

TV lower back panel

HDMI device

VIDEO

AUDIO

HDMI OUT

L

R

 

IN IN

OUT

LR

To view the HDMI device video:

Select the HDMI 1, HDMI 2, or HDMI 3 video input source on the TV.*

*To select the video input source, press INPUT on the remote control (- page 21). To program the TV remote control to operate other devices, see Chapter 3.

To connect a DVI device, you will need:

•one HDMI-to-DVI adapter cable (HDMI type A connector) per DVI device

–For proper operation, the length of an HDMI-to-DVI adapter cable should not exceed 9.8 ft (3m). The recommended length is 6.6 ft (2m).

•one pair of standard analog audio cables per DVI device

–An HDMI-to-DVI adapter cable transfers video only. Separate analog audio cables are required (see illustration).

–See “Setting the HDMI™ audio mode” (- page 32).

TV upper back panel

 

 

 

 

 

 

 

 

 

 

TV lower back panel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVI device

VIDEO

AUDIO

DVI/HDCP

L

R

OUT

 

IN IN

 

 

OUT

L

R

Note: To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these procedures:

•When turning on your electronic components, turn on the TV first, and then the HDMI or DVI device.

•When turning off your electronic components, turn off the HDMI or DVI device first, and then the TV.

[1]EIA/CEA-861-D compliance covers the transmission of uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of high- definition video signals. Because this is an evolving technology, it is possible that some devices may not operate properly with the TV.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 32HL17 32HL17U 37HL17 42HL17 32HL37 32HL37U Dear Customer Safety PrecautionsInstallation, Care, and Service Important Safety InstructionsAdditional Safety Precautions InstallationCare ServiceChoosing a location for your LCD TV To Display your LCD TV using a Wall BracketTo Display your LCD TV on the included Pedestal Stand Removing the Pedestal StandTrademark Information PartImportant notes about your LCD TV Contents Welcome to Toshiba Features of your new TVIntroduction Introduction HD1, ColorStream HD2, Hdmi 1, Hdmi 2, Hdmi 3, PC TV front and side panel controls and connectionsGreen and Yellow LEDs ColorStream HD-1 and ColorStream HD-2 TV back panel connectionsAbout the connection illustrations Connecting your TVOverview of cable types To view the antenna or Cable signal Connecting a VCR and antenna or Cable TV no Cable boxYou will need To view the VCRTo view basic and premium Cable channels Connecting a VCR with S-video and a cable boxCoaxial cables Video cable Standard audio cablesTo view the DVD player To view antenna or Cable channelsTo view the VCR or view and record antenna channels To record a TV program while watching a DVDSelect the Video 2 video input source on the TV Connecting a camcorderTo view the camcorder video To connect an Hdmi device, you will need Connecting an Hdmi or DVI device to the Hdmi inputTo view the Hdmi device video To connect a DVI device, you will needTo control the audio Connecting an audio systemTo connect a PC to the Hdmi terminal on the TV Connecting a personal computer PCTo connect a PC to the PC in terminal on the TV Preparing the remote control for use Using the remote controlInstalling the remote control batteries Remote control effective rangeLearning about the remote control To use your TV remote control to operate a Using the remote control to control your other devicesVCR, set the Mode Select switch to AUX DVD player or HTIB, set the Mode Select switch toAUX 1 VCR Remote Control functional key chartProgramming the remote control to control your other devices Satellite receiver Cable converter boxTV/VCR Combo DVD/VCR ComboHtib Icon Option Menu layout and navigationMain menu layout Setup menu Setup/Installation menu layoutInstallation Navigating the menu systemTo configure the ANT input source Setting up your TVSelecting the menu language To select the menu languageManually adding and deleting channels in the channel memory Programming channels automaticallyTo program channels automatically To add or delete channels in the channel memoryLabeling channels To set the Hdmi audio mode Setting the Hdmi audio modeTo create and assign a custom label To delete the custom labelViewing the system status Viewing the digital signal meterReset Factory Defaults To cancel the reset Selecting the Power-On ModeTo set the Power-On Mode feature Highlight No and press TSelecting the video input source to view Using the TV’s featuresLabeling the video input sources To select the video input source to viewFavorites Browser Tuning channelsTuning channels using Channel Browser Adding and clearing channels and inputs in the History List Elements of the Channel BrowserSwitching between two channels using SurfLock Tuning to a specific channel programmed or unprogrammedSwitching between two channels using Channel Return Natural picture size Selecting the picture sizeTheaterWide 1 picture size for 43 format programs TheaterWide 2 picture size for letter box programsFull picture size for 169 480i, 480p source programs only To set the scroll settingsTo turn off the auto aspect ratio feature To turn on the auto aspect ratio featureTo set the Cinema Mode to Film To set the Cinema Mode to VideoAdjusting the picture quality Adjusting the pictureSelecting the picture mode Digital CC Settings Using the closed caption modeBase closed captions To view captions or textUsing the digital audio selector Adjusting the audioCC Selector Muting the soundTo adjust the audio quality Adjusting the audio qualitySelecting stereo/SAP broadcasts To listen to stereo soundUsing the Dolby Digital Dynamic Range Control feature Using the StableSound featureEntering the PIN code Using the Locks menuIf you cannot remember your PIN code Changing your PIN codeBlocking TV programs and movies by rating V-Chip Press b to highlight Enable Rating BlockingTo block and unblock TV programs and movies To download the additional rating system if availableTo unblock individual channels Blocking channelsTo block channels Unlocking programs temporarily Using the input lock featureUsing the control panel lock feature Using the PC settings featureTo adjust the PC settings To lock the control panelSetting the sleep timer Setting the PC AudioUnderstanding the last mode memory feature Understanding the auto power off featureTo display TV status information using Recall To display TV status information using InfoUsing the advanced picture settings features Using the TV’s advanced featuresUsing dynamic contrast Using the static gamma featureUsing CableClear digital noise reduction Selecting the color temperatureTo select the color temperature To change the CableClear settingsUsing the Game Mode feature Using Mpeg noise reductionTo turn on Game Mode To turn off Game ModeUsing the SRS WOW surround sound feature Using the advanced audio settings featuresTo adjust the WOW settings On or OffGeneral troubleshooting TroubleshootingRating blocking V-Chip problems Channel tuning problemsClosed caption problems LED indications LED Indication Condition SolutionAppendix SpecificationsFormat Resolution Frequency Pixel Clock Frequency For LCD Televisions 26 and Larger Limited United States WarrantyFor Toshiba Brand Flat Panel Televisions Limited Canadian WarrantyDisclaimer and Limitation of Remedy Appendix 13, 14 IndexPage Page Page 07-05
Top Page Image Contents