Toshiba 65HT2U owner manual Setting the sleep timer, Automatic Power Down, No Signal Power Down

Page 46

Chapter 6: Using the TV’s features

Setting the sleep timer

You can set the sleep timer to turn off the TV after a set length of time (maximum of 12 hours).

To set the sleep timer using the remote control:

Press on the remote control to set the length of time until the TV turns off. Repeatedly press to increase the time in 10-minute increments, or press

or to increase or decrease the time in 10-minute increments, to a maximum of 12 hours.

To set the sleep timer using the on-screen menus:

1Press and open the Setup menu.

2Highlight Sleep Timer and press .

3Press the number buttons to enter the length of time in 10-minute increments.

4Press .

Note: When a power failure occurs, the sleep timer setting may be cleared.

To display the remaining sleep time:

Press .

To cancel the sleep timer:

Press repeatedly or press or until it is set to 0 minutes.

Automatic Power Down

The TV will automatically turn itself off (standby) after 4 hours, if you do not operate the TV either from the remote control or the TV control panel.

1From the Preferences menu, highlight Energy

Saving Settings and press .

2Press or to select Automatic Power Down. 3Press or to select On or Off, and press .

Note:

The Default setting of this feature is off.

1 minute before switching to standby, a warning message will appear.

When the following features are set, the feature that is set for the nearest time will function.

−−Automatic Power Down

−−Sleep Timer

−−No signal auto power off (after 15 minutes of no signal)

No Signal Power Down

The TV will automatically turn itself off after 15 minutes when no signal is detected.

You can change the setting to Off for the following purposes:

Low signal strength of analog channel (no signal detection.)

Only Audio L/R is connected to external input to listen to music through the TV speakers.

1From the Preferences menu, highlight Energy

Saving Settings and press .

2Press or to select No Signal Power Down

and press .

3Press or to highlight the item you want to change, and press or to select On or Off.

Note:

The default setting of this feature is On.

A warning message will appear 1 minute before turning off.

(continued)

46

Image 46
Contents 65HT2U Safety Precautions Dear CustomerInstallation, Care, and Service Important Safety InstructionsAdditional Safety Precautions InstallationCare On a bed, sofa, rug, or Similar surfaceChoosing a location for your LCD TV ServiceTo Display your LCD TV using a Wall Bracket To Display your LCD TV on the included Pedestal StandRemoving the Pedestal Stand TV Size Hole PatternHxV400x400 mm 65 TVTrademark Information Important notes about yourOperation is subject to the following two conditions Contents Introduction Features of your new TV1920 x 1080 output resolution CableClear digital picture noise reduction Introduction TV front and side panel controls and connections Power LED Green = Power indicator1無 Green LED 3無 PC in For use when connecting a personal computer Power CordTV back panel connections Overview of cable types Connecting your TVAbout the connection illustrations Connecting a VCR, Antenna, Cable TV, or Camcorder To view the VCR or view and record antenna channels To view antenna or Cable channelsTo view the DVD player To record a TV program while watching a DVDTo connect a DVI device, you will need To connect an Hdmi device, you will needTo view the Hdmi device video One HDMI-to-DVI adapter cableHdmi cables  REGZA-LINKconnectionBefore controlling the devices TV back panel Audio receiverTo control the audio Connecting a digital audio systemConnecting a personal computer PC To connect a PC to the PC in terminal on the TVGround Reserved Signal names for mini D-sub 15-pin connectorPin Signal Name Ground Sync ReservedInstalling the remote control batteries Using the remote controlRemote control effective range  page 31 or to edit the Favorites List  Learning about the remote control9無 Recall displays TV status information  Main menu layout Menu layout and navigationIcon Option Setup/Installation menu layout Navigating the menu systemTo configure the ANT/CABLE input source Setting up your TVInitial Setup Selecting the menu languageTo program channels automatically Setting channel skipProgramming channels into the TV’s channel memory Scan, and press again to begin channel programmingSetting the Hdmi audio mode Reset Factory Defaults Viewing the digital signal meterSetting the time zone Viewing the system statusLabeling the video input sources Using the TV’s featuresSelecting the video input source to view To select the video input source to viewTuning channels using Channel Browser Tuning channelsFavorites Browser Elements of the Channel Browser Adding and clearing channels and inputs in the History ListTuning to the next programmed channel Setting the Channel Tuning ModeSwitching between two channels using Channel Return Selecting the picture size Switching between two channels using SurfLockFor 1080i, 1080p and 720p signal program source Full For 169 480i, 480p source programs onlyNative TheaterWide For letter box programsTheaterWide For letter box programs with subtitles NormalUsing the auto aspect ratio feature Using the Freeze featureAdjusting the picture Selecting the picture modeAdjusting the picture quality Using the closed caption modeBase closed captions CC Selector Digital CC SettingsBase CC Mode setting To customize the closed captionsAdjusting the audio quality Adjusting the audioUsing the digital audio selector Muting the soundSelecting the optical audio output format Using the Locks menuUsing the Dolby Digital Dynamic Range Control feature Entering the PIN codeBlocking TV programs and movies by rating V-Chip 4無 Press  to highlight Enable Rating BlockingChanging your PIN code To block and unblock TV programs and moviesBlocking TV programs by Canada rating Press  to highlight Enable Rating BlockingCanadian Rating Menu will appear Unlocking programs temporarily Using the input lock featureUsing the GameTimer Locking channelsTo adjust the PC settings Using the PC settings featureUsing the panel lock feature To lock the panelUsing the Media Player with USB Setting the PC AudioUsing the Media Player To select the Auto Start functionSlideshow Viewing photo filesSingle View Playing music filesDuring playback To set the repeat modeTo close the Music Player Automatic Power Down Setting the sleep timerNo Signal Power Down REGZA-LINKplayback device DVD player, etc. control Using REGZA-LINKAvailable remote control key functions REGZA-LINKinput source selectionTo display TV status information using Recall Volume and Mute controls of Audio ReceiverTo set the REGZA-LINKSetup Displaying TV status informationTo close the screen Understanding the last mode memory featureTo display TV status information using Info Press againUsing Dynamic Contrast Using the TV’s advanced featuresUsing the advanced picture settings features Using the static gamma featureUsing the Film Stabilization feature Selecting the cinema modeUsing the ClearFrame feature Using CableClear digital noise reductionTo turn on Game Mode Using Mpeg noise reductionUsing the Game Mode feature To turn off Game ModeTroubleshooting General troubleshootingChannel tuning problems Sound problemsRemote control problems Closed caption problemsSpecifications AppendixHdmi signal formats Acceptable signal formats for PC in and Hdmi terminalsPC in signal formats Format Resolution Frequency Pixel Clock FrequencyRental Units Limited United States Warranty for LCD TelevisionsHow to Obtain Warranty Service Your ResponsibilityLimited One 1 Year Warranty on Parts and Labour Disclaimer and Limitation of Remedy Arbitration and Dispute ResolutionCritical Applications How to Obtain Warranty Services General ProvisionsPage Toshiba America Information SYSTEMS, INC