Sony HCD-RG40 specifications HCD-DX30/RG40, Safety CHECK-OUT, Leakage

HCD-DX30/RG40

Tape deck section

Recording system	4-track 2-channel stereo
Frequency response	40 – 13,000 Hz (± 3 dB),
	using Sony TYPE I
	cassette

Tuner section

FM stereo, FM/AM superheterodyne tuner

FM tuner section
Tuning range	87.5 – 108.0 MHz
Antenna	FM lead antenna
Antenna terminals	75 ohm unbalanced
Intermediate frequency	10.7 MHz

AM tuner section

Tuning range

US, Canadian, Mexican, Argentina models:

	530 – 1,710 kHz (with the
	interval set at 10 kHz)
	531 – 1,710 kHz (with the
	interval set at 9 kHz)
European and Middle Eastern models:
	531 – 1,602 kHz (with the
	interval set at 9 kHz)
Other models:	531 – 1,602 kHz (with the
	interval set at 9 kHz)
	530 – 1,710 kHz (with the
	interval set at 10 kHz)
Antenna	AM loop antenna
Antenna terminals	External antenna terminal
Intermediate frequency	450 kHz
General
Power requirements
US, Canadian models:	120 V AC, 60 Hz
European models:	230 V AC, 50/60 Hz
Australian models:	230 – 240 V AC,
	50/60 Hz
Mexican models:	120 V AC, 50/60 Hz
Other models:	120 V, 220 V or
	230 – 240 V AC,
	50/60 Hz
	Adjustable with voltage
	selector
Power consumption
USA models:
HCD-RG40:	140 watts
Canadian models:
HCD-RG40:	140 watts
European models:
HCD-RG40:	140 watts
HCD-RG40:	0.5 watts (at the Power
Other models:	Saving Mode)
HCD-DX30:	175 watts
Dimensions (w/h/d)	Approx. 280 ⋅ 325 ⋅ 421 mm
Mass
North American models:
HCD-RG40:	Approx. 9.0 kg
European models:
HCD-RG40:	Approx. 9.0 kg
Other models:
HCD-DX30:	Approx. 10.0 kg

Design and specifications are subject to change without notice.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.

LEAKAGE

The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods.

1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments.

2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job.

3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A)

To Exposed Metal

Parts on Set

			AC
0.15 ∝ F		Ω	Voltmeter
	1.5 k		(0.75 V)

Earth Ground

Fig. A. Using an AC voltmeter to check AC leakage.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS

LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

2