Toshiba 34HFX85 appendix Connecting a DVD player/satellite receiver and a VCR

Page 9

Connecting a DVD player/satellite receiver and a VCR

This connection allows you to watch DVD/satellite, VCR, or TV programs. You can record from the satellite receiver and TV, as well as record one TV channel while watching another channel.

From satellite

DVD player / Satellite Receiver

OUT

L

Satellite IN

R

You will need:

•three coaxial cables

•two sets of standard A/V cables

•one S-video cable

•one pair of standard audio cables

Note:

You can use a standard video cable instead of the S-video cable, but the picture quality will decrease. If you use an S-video cable between the TV and DVD player/satellite receiver, make the audio connections but remove the standard video cable. Do not connect both an S-video and a standard

Safeguards

Important

ToshibaWelcome to

S-VIDEO

TV

From antenna

AUDIO

video cable to VIDEO1 (or VIDEO2) at the same time or the picture performance will be unacceptable.

The unauthorized recording, use, distri- bution or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

yourConnecting TV

Remote ControlUsing the

Stereo VCR

		IN
	IN from ANT	OUT to TV
		OUT
	CH 3	L	R
	CH 4	L	R
	CH 4	VIDEO	AUDIO
		VIDEO	AUDIO

9

your TVSetting up

FeaturesUsing the TV’s

Appendix

J3U00321B(E)_P07-15

9

9/08/2005, 10:31 AM

Image 9

Contents 34HFX85 Computer PC. This TV is not intended for use With a PC Dear CustomerImportant Safety Instructions Care Connecting your TV Important Safety Information Welcome to ToshibaUsing the remote control Setting up your TVExploring your new TV Welcome to ToshibaSelecting a location for the TV TV front panelConnecting your TV Connecting a VCRStereo VCR Connecting a cable converter box or Antenna Converter/Descrambler Splitter SwitchFrom Cable Connecting a DVD player/satellite receiver and a VCR DVD player with Component video DTV Receiver With Component video Connecting two VCRs Connecting a camcorder To connect a DVI device, you will need Connecting an Hdmi or a DVI device to the Hdmi inputConnecting an audio system AmplifierYou will need One pair of standard audio cables Preparing the remote control for use Using the remote controlInstalling the remote control batteries Mode DeviceRemote control functional key chart Disc shift Deck side Disc shiftStop RecordSearching and sampling the code of a device Press Mode to select the TV mode to control the TVOperational feature reset Using the volume lock featureDevice code table VCR setup codesCD Player setup codes Learning about the remote control Setting up your TV Starting setupChanging the on-screen display language Adding channels to the TV’s memory Image tilt correctionProgramming channels automatically Adding and erasing channels manuallyAdjusting the channel settings Using the TV’s featuresSwitching between two channels Changing channelsSelecting a password Using the Locks menuTo select your password and access the Locks menu To clear your favorite channelsUsing the V-Chip parental control feature To lock channels Locking channelsPress Enter . Repeat steps 1 through 6 to lock To unlock channelsLocking the video inputs Setting the GameTimerTMLabeling channels Using the front panel lock featureSelecting the video input source Labeling the video input sourcesTo label the video input sources Select Conventional 43 picture On a conventional TV This mode cannot be scrolledScreen Center of the picture remainsTheaterWide 2 picture size for letter box programs Full picture size for 169 source programsTheaterWide 3 picture size example Press Scrolling the TheaterWide picture TheaterWide 2 and 3 onlyTo raise the picture, press To lower the picture, pressSelecting the cinema mode Using the Aspect featureSelecting the display format for 480p signals only Adjusting the picture quality Adjusting the picture Selecting the picture modeTo select the picture mode To adjust the picture qualitySelecting the color temperature Using the CableClear featureSelecting the Scan Velocity Modulation SVM Resetting your picture adjustments Setting the sleep timerUsing the closed caption feature Adjusting the sound quality Adjusting the sound Muting the soundTo adjust the sound quality Selecting stereo/SAP broadcastsResetting your audio adjustments Using the StableSound featureUsing the BBE sound feature Turning off the built-in speakers Selecting the Hdmi audio input sourceDisplaying TV status information on-screen Understanding the Power Return feature Auto power offTroubleshooting Symptom SolutionSpecifications Limited United States Warranty Memo National Service Division