Toshiba DKVR60KU owner manual Troubleshooting, Symptom Remedy, Timer SET

TROUBLESHOOTING

Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation.

	Symptom	Remedy
	The power does not turn on.	• Check that the AC power cord is connected securely.
		• Check the breaker (in case of power failure).
		• Press [TIMER SET] to cancel the timer standby mode.
	There is no picture.	• Re-connect the connecting cords securely.
		• Check if the connecting cords are damaged.
		• Check the connection to your TV (page 19-22).
		• Check if the progressive scan mode is set correctly according to your TV
		(page 95).
		• Switch the input selector on your TV (such as to “L1”) so that the signal
		from the unit appears on the TV screen.
	Cannot record a TV program.	• This unit does not have a tuner to receive TV broadcasting.
		• You must connect this unit to an external tuner to record TV programs
		(page 19).
	TV program pictures are distorted.	• Check if all the connections are made correctly (page 19).
	Playback picture is distorted.	• Keep the device which may cause electrical disturbances, such as a
		cellular phone, away.
	Playback picture or TV program from	• If the playback picture output from a DVD player, VCR or tuner goes
	the device connected through the unit	through the unit before reaching your TV, the copy-protection signal
	is distorted.	applied to some programs could affect picture quality. Disconnect the
		playback device in question and connect it directly to your TV.
	There is no sound.	• Re-connect all connections securely.
		• Check if the connecting cord is damaged.
		• Check the connections to the amplifier input.
		• Check if the input device setting on the amplifier is correct.
		• When the unit is in pause mode or in slow-motion playback mode,
		sound is not output. This is not a malfunction.
D		• When the unit is in fast forward or fast reverse mode, sound is not
V		output. This is not a malfunction.
		• If the audio signal does not come through the DIGITAL AUDIO OUT
D
		(COAXIAL) jack, check the setting in “Audio Out” (page 90).
•		• While the setup menu or timer programming display is shown, or while
		the screen saver is active, the audio is muted.
V
	No DTS sound on digital output.	• Change the setting menu for “DTS” to “ON”.
C
	No DTS sound from analog output	• This unit has no analog sound output when playing back the selected
R		DTS sound mode.
	Nothing was recorded even though	• There was a power failure during recording.
	you set the timer setting correctly.	• The unit’s internal clock stopped due to a power failure that lasted for
		more than 30 seconds. Reset the clock (page 26).
		• The program contains copy protection signals that restricts copying.
		• The timer setting overlapped with another setting that has priority.
	Timer recording does not start.	• No disc is inserted.
		• A disc is not recordable (finalized DVD-RW/-R, finalized DVD+R, a fully
		recorded disc, etc.).
	Timer recording is not complete or did	• The timer setting overlapped with another setting that has priority
	not start from the beginning.	(page 42).
		• Disc space was not enough.
		• “Make Recording Compatible“ is not set to “ON”, when recording onto
		DVD+RW/+R that was recorded on other unit.
	Timer recording is impossible.
		• Make sure	appears on the front panel display of this unit. If not, press
		[TIMER SET].
	The remote control does not function.	• Batteries are weak.
		• There are obstacles between the remote control and the unit.
		• The remote control is far from the unit.
		• There are no batteries in the remote control.
		• Check if the unit is turned on.
		• The remote control is not pointed at the infrared sensor window on the unit.
		• Press [DVD] or [VCR], whichever you need. Then, try again.
		• Press [TIMER SET] to cancel the timer standby mode.
	The unit does not operate properly.	• When static electricity, etc., causes the unit to operate abnormally,
		unplug the unit and then plug it in again.
			EN 103

Disc Introduction Connections Basic Setup Management Recording Playback Editing Function Setup VCR Function Others

E9PKBUD_DKVR60KU_EN.indd 103

8/11/2009 4:01:54 PM