Bel Canto Design PL-1A manual Why won’t the disc I loaded play?

Page 21

Getting Started

04

•After I load a DVD disc, it ejects automati- cally after a few seconds!

Most likely, the disc is the wrong region for your player. The region number should be printed on the disc; check it against the region number of the player (which you can find on the rear panel).

If the region number is OK, it may be that the disc is damaged or dirty. Clean the disc and look for signs of damage. Check also that the disc is aligned properly in the disc tray and that it’s loaded label-side up.

•Why won’t the disc I loaded play?

First check that you loaded the disc the right way up (label side up), and that it’s clean and not damaged.

If a disc loaded correctly won’t play, it’s probably an incompatible format or disc type, such as DVD-ROM.

•There’s no picture!

Check the front panel and make sure that the VIDEO OFF indicator isn’t lit. If it is, press the VIDEO OFF button to switch the video output back on.

Also make sure that if your TV isn’t compatible with progressive scan video, that the PROGRESSIVE indicator isn’t lit. If it is, press the PROGRESSIVE button to switch the video output back to interlace. See also page 18.

•I have a widescreen TV so why are there black bars at the top and bottom of the screen when I play some discs?

Some movie formats are such that even when played on a widescreen TV, black bars are necessary at the top and bottom of the screen. This is not a malfunction.

•I have a standard (4:3) TV and set the player to show widescreen DVDs in pan & scan format, so why do I still get black bars top and bottom with some discs?

Some discs override the display preferences of the player, so even if you have 4:3 (Pan & Scan) selected, those discs will still be shown in letterbox format. This is not a malfunction.

•My AV receiver is definitely compatible with 96/88.2kHz Linear PCM audio, but it doesn’t seem to work with this player. What’s wrong?

For digital copy-protection purposes, some 96/88.2kHz DVD discs only output digital audio downsampled to 48/44.1kHz. This is not a malfunction. To fully take advantage of the high sampling rate audio, connect the analog audio outputs to your amplifier/receiver.

•Why can’t I hear SACD audio through the digital outputs?

SACD audio is only available through the analog outputs. This is not a malfunction. Some DVD-Audio discs too only output audio through the analog outputs.

7

31

20

En

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Rev.3 3/22/04 Table of Contents Congratulations Important Safety Instructions Important Notice For U.S. modelAdditional Saftey Requirements DVD-Audio and Sacd compatible Before You Start FeaturesPhoto CD / DVD-RAM / DVD-ROM General Disc CompatibilityCDs, SACDs and Video CD are divided into tracks Before You StartPage Page Controls and Displays Enter & Joystick Controls and Displays Remote controlReturn Number buttonsSetting up the Remote Control to Preset code listSetting up with the Setup Navigator Getting Started Using the on-screen displaysSelect ‘Setup Navigator’ JoystickGetting Started Select a DVD languageDid you connect this player to an AV receiver? Congratulations, setup is complete Basic playback controls Getting Started Playing discsPress 0 OPEN/CLOSE to open the disc tray Load a disc Press 3 play to start playbackDVD disc menus Front panel controlsStops playback ¢ Skips to the next track or chapterNumbers Video CD PBC menusWhy won’t the disc I loaded play? Disc may have been illegally copied Some MP3 tracks don’t show up. Where are they?Playing Discs Introduction Using the Disc Navigator to browse the contents of a discMP3 For CDs and Video CDs select a trackUsing the Multi Dial Playing Discs Scanning discsTo resume normal playback, press Play Frame advance/frame reverse Playing Discs Playing in slow motionPress repeatedly to change the slow motion speed Slow motion speed is displayed on- screenPlaying Discs Looping a section of a disc Press Enter on ‘BEnd Point’ to set the loop end pointPress Enter on ‘AStart Point’ to set the loop start point Playing Discs Using repeat play Select a random play option Playing Discs Using random playRandom Title Random Chapter Random Off Random Group Random Track Random OffSelect ‘Create/Edit’ from the list of program options Playing Discs Creating a program listProgram list can contain up to 24 titles Chapters/groups/folders/tracksTo play the program list, press Editing a program list Other functions available from the program menuSelect a program play function Press Enter to start playback Playing Discs Searching a discSwitching DVD-Video audio language Playing Discs Switching subtitlesPress Subtitle repeatedly to select a subtitle option Press Audio repeatedly to select an audio language optionSwitching DVD-Audio audio channel Playing Discs Switching DVD-RW audio channelSwitching CD/MP3/Video CD audio channel Switching camera anglesDuring PBC playback only Playing Discs Displaying disc informationAudio Settings Menu Audio DRC TruSurround’ or ‘Off’, as required Audio Settings Menu Virtual SurroundSet the distance for each speaker Audio Settings MenuCreating your own interlace output presets Video Settings Menu Video Adjust Interlace OnlyUse the joystick left/right to select a preset Adjust the picture quality settingsVideo Settings Menu Creating your own progressive output presetsAjust the picture quality settings Digital Audio Out settings Initial Settings Menu Using the Initial Settings menuDigital Out Dolby Digital Out427 Video Output settings Initial Settings MenuTV Screen Video OutDefault setting Auto Language settingsDefault setting English Still PictureSubtitle Language Auto Language Default setting English Default setting OnDVD Menu Language Display settingsSubtitle Display OSD LanguageOptions Angle IndicatorBackground Screen SaverUse the number buttons to enter a 4- digit password Select ‘Password’Select ‘Password Change’ Enter a new passwordSelect ‘Level Change’ Use number buttons to enter your password, then press EnterSelect a new level Select ‘Country Code’Auto Disc Menu Bonus GroupDefault setting Single Default setting DVD-Audio Group Playback DVD Playback ModeDefault setting 2ch Area Sacd PlaybackAudio Output Mode Initial Settings Menu CD PlaybackSpeaker Installation SpeakersDefault setting all speakers 10 ft Speaker DistanceL and R speakers are paired you can’t set them differently Channel Level Handling discs Additional Information Taking care of your player and discsStoring discs Discs to avoidAdditional Information Additional Information Screen sizes and disc formats Resetting the playerWidescreen TV users Standard TV usersBitstream*3 Additional Information About the audio output settingsCountry code list Additional Information Language code listLanguage Language code letter, Language code Country, Country code, Country code letterGlossary Mpeg video Mpeg audioPacked PCM DVD-Audio only PCM Pulse Code ModulationAdditional Information Troubleshooting Video OFF button No picture/No colorScreen is stretched or aspect does not change No audio, or audio is dis- tortedCD volume Disc containing the MP3 tracks won’t play Make sure that Audio Output Mode is set to 2 ChannelCan’t hear effect TruSurroundGeneral Additional Information SpecificationsBel canto PLayer-1A Command Details and Explanation RS232-Interface Usage Details Command Command RS232 Hardware Connections

PL-1, PL-1A specifications

Bel Canto Design has long been synonymous with high-performance audio equipment, and its PL-1A and PL-1 models are no exception. These preamplifiers stand out in the world of high-fidelity audio for their refined technology, elegant design, and exceptional sound quality.

The Bel Canto PL-1A is a state-of-the-art digital preamplifier that caters to audiophiles demanding precision and versatility. It features a fully balanced signal path, which helps to minimize noise and distortion, ensuring that the music signal remains pure and unaltered. The PL-1A employs advanced digital signal processing technology, which not only enhances the audio performance but also provides a range of connectivity options to accommodate various audio sources.

One of the standout features of the PL-1A is its high-resolution asynchronous USB input, allowing users to connect their computers or digital audio players seamlessly. This input supports high sample rates, making it ideal for high-definition audio formats. Additionally, it includes multiple digital inputs such as coaxial and optical, along with analog inputs, providing flexibility for integrating different audio components.

The PL-1A also comes with an intuitive user interface, making it easy to navigate through the various settings and options. The remote control allows users to adjust volume levels, select inputs, and control other features without the need to get up from their listening position, enhancing the overall convenience.

The design of the PL-1A is not just functionally excellent but also visually appealing. Its sleek chassis is made of high-quality materials, giving it a premium look and feel that complements any audio setup. The attention to detail in both the design and craftsmanship ensures that it not only performs exceptionally well but also stands the test of time.

On the other hand, the Bel Canto PL-1 serves as a more traditional analog preamplifier, offering a warm, rich sound that many audiophiles crave. It features a robust power supply, low-noise circuits, and high-quality components that contribute to its stellar audio performance. The PL-1 is designed for both vinyl enthusiasts and digital audio lovers, providing inputs for turntables as well as digital sources.

Both models embody Bel Canto Design’s commitment to quality, innovation, and state-of-the-art audio technologies, making them ideal choices for anyone looking to elevate their listening experience. With their advanced features, aesthetic appeal, and superior sound quality, the Bel Canto PL-1A and PL-1 preamplifiers promise to satisfy even the most discerning audiophiles.
Top Page Image Contents