Philco PVD2000 Quick Use Guide, Connections, Clock Set Up, VCR/DVD Switching, RF Output Channel

Quick Use Guide

1	Connections	3 Press [B] to start Auto Set Up.	CH 01
Please refer to “Basic TV Connection” on the front page			AUTO SET UP
before you use this unit.

RF Output Channel

If channel 3 has been already occupied for broadcasting,

1)Set your TV to channel 4.

2)Insert a pre-recorded tape into this unit.

3)Press [SOURCE] on the unit so that the VCR SOURCE light is lit.

•If noise appears on the TV screen, press [VCR/TV] on the remote control.

4)Press [PLAY B] once.

5)After a few seconds, press and hold [PLAY B] on the unit for 3 seconds.

•The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.

•When a picture does not appear on the TV screen, repeat step 4.

6)Press [STOP C] to stop playback.

2 Installing the Batteries for the Remote Control

1 2 3

Do you connect the cable from the cable box or the satellite box to the unit’s ANT-IN jack?

YES NO

Yes Press [MENU] to exit.

No Please wait for a few minutes.

After scanning...

•The tuner stops on the lowest memorized channel.

•You can select only the channels memorized in this unit by using [SKIP/CH. G/K, H/L] (or [CHANNEL K/L]).

•If “AUTO SET UP” appears on the TV screen again, check the cable connections. Then, press [B] once again.

5	Clock Set Up
	VCR
1	Press [MENU] and select “CLOCK SET“.	- M E N U -
	Then press [B] to go to next step.	TIMER PROGRAMMING
		AUTO REPEAT [OFF]
	MENU	CHANNEL SET UP
		B CLOCK SET

or

LANGUAGE SELECT

✄

3 VCR/DVD Switching

STANDBY-ON SPEED		OPEN/CLOSE
	AUDIO	/EJECT

	1	2	3
			SKIP/CH.
	4	5	6
			VCR/TV
	7	8	9
			SLOW
VCR button		0	+10
	DISPLAY	VCR	DVD PAUSE

DVD button

PLAY

		SOURCE button		STOP
VCR			RECORD
		DVD
			MENU		ENTER
			SETUP	TOP MENU		RETURN
			MODE	ZOOM	SEARCH	CLEAR/
		DVD SOURCE light			MODE	C. RESET
	SOURCE		T-SET	ANGLE	REPEAT	A-B
			SUBTITLE
		VCR SOURCE light

VCR MODE

Press [VCR] on the remote control. (Verify that the VCR SOURCE light is lit.)

DVD MODE

Press [DVD] on the remote control. (Verify that the DVD SOURCE light is lit.)

Hint

•Pressing only [SOURCE] on the front panel DOES NOT switch the mode of the remote control. You MUST select the correct mode on the remote control.

•If the clock is not set, the CLOCK SET screen appears when you press [MENU]. In this case, go to step 2.

2	Select the current month.	MONTH DAY			YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/	– –	– – – –
		HOUR MINUTE			AM/PM
	or	– –	:	– –	– –
3	Select the current day.		CLOCK SET
	Then press [B] to go to next step.	MONTH DAY			YEAR
		1 0	/	0 2	– – – –
		HOUR MINUTE			AM/PM
	or	– –	:	– –	– –
4	Select the current year.	MONTH DAY			YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/	0 2	2 0 0 6
		HOUR MINUTE			AM/PM
	or	– –	:	– –	– –
5	Select the current hour.		CLOCK SET
	Then press [B] to go to next step.	MONTH DAY			YEAR
		1 0	/	0 2 MON 2 0 0 6
	or	HOUR MINUTE			AM/PM
		0 5	:	– –	– –
6	Select the current minute.	MONTH DAY			YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/	0 2 MON 2 0 0 6
		HOUR MINUTE			AM/PM
	or	0 5	:	4 0	– –

4	Turn on the Unit for the First Time
	VCR
1	Turn on the TV and set it to channel 3.
	• If channel 3 has been already occupied for
	broadcasting, see “RF Output Channel” section.
2	Select your language in the first time you turn on this unit.
	Then press [B] to go to next step.	LANGUAGE SELECT
	STANDBY-ON	B ENGLISH	[ON]

FRANCAIS

ESPAÑOL

or

7	Select “AM” or “PM”.		CLOCK SET
		MONTH DAY		YEAR
		1 0	/ 0 2 MON 2 0 0 6
	or	HOUR MINUTE		AM/PM
		0 5	: 4 0	P M AM
				B PM
8	To exit the CLOCK SET screen

– 27 – EN