Philco PVD2000 manual Preparation for Use, Turn on the Unit for the First Time, Clock Setup

Preparation for Use

Turn on the Unit for the First Time

	VCR	Operation described in this manual are
		mainly based on the remote control.
1	Turn on the TV and set it to channel 3.
	• If channel 3 has been already occupied for broadcasting,
	see “RF Output Channel” section on page 6.
2	Select your language when turning this unit on for the first time.
	Then press [B] to go to next step.		LANGUAGE SELECT
	STANDBY-ON		B ENGLISH	[ON]
			FRANCAIS

ESPAÑOL

or

To Preset the Channel Again

1)Press [MENU] until the main menu appears.

2)Select “CHANNEL SET UP” by using [K//L], then press [B].

3)Select “AUTO SET UP” by using [K//L], then press [B]. After scanning, the tuner stops on the lowest memorized channel.

To Change the On-Screen Language

1)Press [MENU] until the main menu appears.

2)Select “LANGUAGE SELECT” by using [K/L], then press [B].

3)Select “ENGLISH” , “FRANCAIS” or “ESPAÑOL” by using [K/L] then press [CLEAR/C.RESET].

Setup

3 Press [B] to start Auto Set Up. CH 01

AUTO SET UP

Do you connect the cable from the cable box or the satellite box to the unit’s ANT-IN jack?

YES NO

Yes Press [MENU] to exit.

• Refer to “Hint for Cable Box or Satellite Box” section on page 6.

No Please wait for a few minutes. After scanning...

•The tuner stops on the lowest memorized channel.

•You can select only the channels memorized in this unit by using [SKIP/CH. G///K, H//L] (or [CHANNEL K///L]).

•If “AUTO SET UP” appears on the TV screen again, check the cable connections. Then, press [B] once again.

Hint

•Repeat these steps only if either there was a power failure or this unit has been unplugged for more than 30 seconds.

To Select a Channel

You can select a channel by using the Number buttons or [SKIP/CH. G/K, H/L].

Notes for using the Number buttons:

•When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number. (for exam- ple: 117, press [1], [1], [7])

•You must precede single-digit channel numbers with a zero. (for example: 02, 03, 04 and so on)

To Add or Delete Channels

VCR

1 Press [MENU] to select “CHANNEL SET UP”.	- M E N U -
Then press [B] to go to next step.	AUTO REPEAT [OFF]
	TIMER PROGRAMMING
MENU	B CHANNEL SET UP
	CLOCK SET
	LANGUAGE SELECT

or

•If the clock is not set, the “CLOCK SET” screen appears when you press [MENU]. In this case, press [MENU] again.

2	Select “MANUAL SET UP”.			CHANNEL SET UP
	Then press [B] to go to next step.			AUTO SET UP
				B MANUAL SET UP
		or
3	Select the channel to be added or deleted.			MANUAL SET UP
				CHANNEL 30	(CATV)
		or		ADD
	or		or
4	Select “ADD” or “DELETE”.			MANUAL SET UP
				CHANNEL 30	(CATV)
		or		DELETE
5	To exit the menu	C. RESET
		CLEAR/

Hint

•If you accidentally select Spanish or French and need English: Press [MENU] and choose SELEC. IDIOMA or SELECTION LANGUE. Press [B] and select ENGLISH. Finally, press [CLEAR/C.RESET].

•To add or delete channels in this unit, [SKIP/CH. G/K, H/L] button works on the channel number memorized in this unit, [K/L] works on all.

Clock Setup

VCR

1	Press [MENU] and select “CLOCK SET”.	- M E N U -
	Then press [B] to go to next step.

		TIMER PROGRAMMING
MENU		AUTO REPEAT [OFF]
		CHANNEL SET UP
		B CLOCK SET
	or	LANGUAGE SELECT

•If the clock is not set, the CLOCK SET screen appears when you press [MENU]. In this case, go to step 2.

2	Select the current month.	MONTH DAY			YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/	– –	– – – –
		HOUR MINUTE			AM/PM
	or	– –	:	– –	– –
3	Select the current day.		CLOCK SET
	Then press [B] to go to next step.	MONTH DAY			YEAR
		1 0	/	0 2	– – – –
		HOUR MINUTE			AM/PM
	or	– –	:	– –	– –
4	Select the current year.	MONTH DAY			YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/	0 2	2 0 0 6
		HOUR MINUTE			AM/PM
	or	– –	:	– –	– –
5	Select the current hour.		CLOCK SET
	Then press [B] to go to next step.	MONTH DAY			YEAR
		1 0	/	0 2 MON 2 0 0 6
		HOUR MINUTE			AM/PM
	or	0 5	:	– –	– –
6	Select the current minute.	MONTH DAY			YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/	0 2 MON 2 0 0 6
		HOUR MINUTE			AM/PM
	or	0 5	:	4 0	– –
7	Select “AM” or “PM”.		CLOCK SET
		MONTH DAY			YEAR
		1 0	/	0 2 MON 2 0 0 6
	or	HOUR MINUTE			AM/PM
		0 5	:	4 0	P M AM
					B PM
8	To exit the CLOCK SET screen

Hint

•To go back one step, press [s] (during steps 2 to 7).

•Your clock setting will be lost if either there is a power failure or this unit has been unplugged for more than 30 seconds.

– 8 – EN