Arcam DV89 manual Video setup

Page 7

Remote type

This informs the player which type of remote control you are using, so that the player can take into account the slight differences between the remote types. For ARCAM remote controls, the remote type is always written on the front of the remote control, normally at the bottom of the unit.

CR-314This selects the grey ARCAM CR-314 remote control

CR-80This selects the black ARCAM CR-80 learning remote control

CR-9000This selects the black ARCAM CR-9000 learning remote control

Other A non-ARCAM learning remote control is being used It is important to choose ‘Other’ if the learning remote in use does not support RC-5 ‘toggle bits’.

OSD (On Screen Display)

This setting controls the ‘pop up’ messages that appear on screen.

On Pop-up messages are enabled

Off No pop-up messages, only menus when required. Certain messages, such as ‘No Disc’ are always shown regardless of how this is set.

Priority

Some DVD discs show different material, or have different behaviour, depending on whether the disc is played on a DVD- video or on a DVD-audio player. The “Priority” option allows you to configure the DV89 to be (primarily) one or other of the player types.

Note that, although this setting may be changed after a disc has been loaded into the DV89, this setting does not take effect unless the disc is re-loaded (or a different disc is played).

Video setup

 

Video 2/7

 

 

TV Shape

4:3 Letter Box

TV System

Auto

Progressive

Off

HQ Video

RGB Scart

NTSC Black

7.5 IRE(Standard)

TV shape

This needs to be set correctly for the type of TV you have and the type of display you prefer.

4:3 Letterbox Use this setting if you have a conventional 4:3

 

TV, and you prefer to view wide screen movies

 

in letterbox format (with black bars at the top

 

and bottom)

4:3 Panscan

Use this setting if you have a conventional 4:3

 

TV, and you prefer to view wide screen movies

 

in Pan & Scan format (cropping the sides of

 

the image)

16:9

Use this setting if you have a wide screen (16:

 

9) TV. Material in 16:9 format is displayed so

 

as to fill the screen.

If you have a 4:3 TV and you have set a preference for Panscan, it does not mean you will always see movies in this format, since the Panscan display must be supported on that disc.

TV System

This is set at the factory to be appropriate for the type of TV used in your country. Should you need to change this setting, the options are explained below.

Auto The video output is taken from that recorded on the disc. When no disc is playing, the logo screen is displayed using the standard of the last disc played.

NTSC NTSC is always used as the video standard. Note that PAL discs are converted to NTSC, but this causes some reduction in the quality of the video output (and may cause the video to become ‘jerky’). This is the best setting to use if your TV can accept only NTSC video (this is generally the case in North America); better results are obtained by using ‘Auto’, but your TV must be able to support PAL.

PAL PAL is always used as the video standard. Note that NTSC discs are converted to PAL, but this causes some reduction in the quality of the video output (and may cause the video to become ‘jerky’). Better results will be obtained by using ‘Auto’, but your TV must be able to support NTSC.

Progressive

Off The video output will always be interlaced (standard definition video). Use this setting if your display device does not support progressive scan.

Auto (525) The component video output will switch to progressive scan mode whenever the output standard is NTSC (525). This would be whenever an NTSC disc is played, or whenever ‘TV System’ is set to NTSC. The video output will revert to interlaced (standard definition) for PAL (625) modes. Use this setting only if your display device supports progressive scan.

On (625/525) The component video output will output progressive scan video for both PAL and NTSC discs. Use this setting only if your TV supports progressive scan in both PAL and NTSC formats.

NOTE: When progressive scan is active, the component video output will be in progressive mode, and the other video outputs (composite and S-Video) are muted.

Since progressive scan must be component, not RGB, the ‘HQ video setting’ will be forced to component if progressive scan is enabled.

Not all displays support progressive scan. If you accidentally enable progressive scan and your display does not support it, you will be unable to view the picture from the DVD player, including the on screen display required to change the video settings. To revert to interlaced mode without using the on screen menus, open the drawer, then press and hold the STOP button on the front panel. The video mode will revert to interlaced mode after the button has been held in for five seconds.

DV89

7

Image 7
Contents Arcam DV89 DVD player Safety instructions Safety guidelinesSafety compliance Disc types supported Using this handbookSafety ContentsInstallation Connecting to a power supply Connecting Digital audioConnecting Analogue audio Remote Control inputConfiguring your DVD player Video setup RGB Scart Audio setupPCM Delay setup Speaker ConfigurationAccess setting Trim setupCompleting the set-up Front panel controls Basic use of your DVD playerPlaying a disc Open Using the remote controlCD/DVD ClearAdvanced controls Special playback modes Advanced features Advanced DVD and VCD featuresJumping to a particular point Hidden groupsGeneral To program a special sequenceDVD-video VCDScreen layout Player modeBrowsing the disc Browse mode Bl When playing CD-ROMs, tag information from MP3Programmed playback CD-ROM Programmed playback Audio CDsShuffle and Repeat Problem Possible cause Solution Reference TroubleshootingProblems with remote controls Problems with video outputProblems with disc playability Problems with audio outputBefore contacting customer services Audio outputs Technical specificationsAccessories supplied Video outputsOn line registration GuaranteeDV89 DV89 Pembroke AVENUE, WATERBEACH, Cambridge CB5 9QR, England Issue