HQ Video (High Quality Video)
This setting controls the type of video given out on the Component and SCART video outputs. It is set at the factory to be appropriate for the type of TV used in your country, so it should not be necessay to change it. If it gets set incorrectly then the picture shown on the TV will have strange colouring.
Component
The video output on both the Component video (3 phonos) and SCART is Y, Pb, Pr component video.
RGB SCART
The video output on both the Component video (3 phonos) and SCART is RGB. Note that if you are using RGB output via phono connectors, you will also need to use COMPOSITE as a sync signal.
NTSC black (Pedestal)
This setting controls the ‘pedestal’ signal or black level when the NTSC video standard is used. Note that it does not affect PAL video in any way.
0 IRE This removes the pedestal from NTSC video. This setting should be used in Japan, and also if you are using RGB video, whatever the country.
7.5IRE This is the standard pedestal level that should be used in all countries that use NTSC video, with the exception of Japan.
Audio setup
| Audio 3/7 |
|
|
Audio | Bitstream/2 Ch. |
Max 48K | |
Pro Logic | Off |
Audio Delay | Not applicable |
This section allows you to configure the type of analogue and digital audio outputs. In particular, the digital output type needs to be set correctly if you are using an external audio decoder, receiver or
Audio
This section allows you to configure the type of analogue and digital audio outputs. In particular, the digital output type needs to be set correctly if you are using an external audio decoder, receiver or
Two different types of digital output are supported: “Bitstream” and “Stereo PCM”.
Bitstream | The Bitstream setting supports the following |
| audio standards: |
| 2 channel PCM (on CDs or DVDs) |
| Dolby Digital |
| MPEG multi channel |
| DTS multi channel |
| Use the Bitstream setting if you have an |
| external decoder that supports Dolby Digital. |
|
|
Stereo | When the “Stereo PCM” digital output is |
PCM | selected, all audio material played is down- |
| mixed to stereo and output as stereo PCM. |
| Use this setting if you have an external |
| converter that supports only |
|
|
| Since the digital and analogue outputs are closely related, the |
DV89 | analogue audio output reflects the digital output type selected. |
|
The options available are as follows:
Bitstream | The digital output is “Bitstream” (as described |
+ 6 Ch. | above). The analogue audio will comprise up |
| to six channels of output, depending on the |
| source material, the speaker configuration |
| (see the “Speaker Setup” section) and the “Pro |
| Logic” setting (see below). |
|
|
Bitstream | The digital output is “Bitstream” (as described |
+ 2 Ch. | above). The analogue audio will comprise |
| a |
| material. |
|
|
PCM | The digital output is “Stereo PCM” (as |
+ 2 Ch. | described above). The analogue audio will |
| comprise a |
| source material. |
|
|
Pro Logic
This controls “Pro Logic” decoding. Pro Logic decoding creates a
Off No Pro Logic processing is performed.
On Pro Logic processing is performed on all appropriate
Auto Pro Logic processing is performed when the audio track on the DVD is indicated as being Dolby Surround encoded.
Note the following points:
If
If the player is configured to have only two speakers connected to it (described in the next section), then no Pro Logic decoding will be performed.
MP3 files, together with
Audio delay
This item is not applicable for the DV89, and should not be changed.
Down-sample
This needs to be set correctly if you are using an external audio decoder, receiver or
Max 96K Choose this option if your external audio decoder is able to process digital audio with a sample rate of up to 96kHz, or if you are not using the digital audio outputs. This is the maximum sample rate present on
Max 48K Choose this option if your external audio decoder is unable to process digital audio with a sample rate of up to 96kHz.
NOTE: This setting is relevant only to the output from
8