Integra DPS-8.3 Video Output Component 1 jacks, Video Output S Video jack, RS-232 port, AC Inlet

Index to Parts and Controls

■Rear panel

1 2 3 4 5 6

	COMPONENT 1
Y	PB	PR

VIDEO

OUTPUT

S VIDEO VIDEO

	COMPONENT 2
Y	PB	PR

RS-232

AC INLET

CH 1

CH 2

FRONT

SURR 1

CENTER

SURR 2

IR

12V

IN

TRIG-

SACD & DVD AUDIO/VIDEO PLAYER

L

L

GER

MODEL NO. DPS-8.3

ANALOG

SURR

OUT

OUTPUT

1

1+2

DIGITAL

R

R

OUTPUT

OUT

SUB

OPTICAL

COAXIAL

REMOTE

WOOFER

CONTROL

7

8

9 0

-

=

~ ! @

Shapes of jacks vary depending on the area in which it was purchased.

1VIDEO OUTPUT COMPONENT 1 jacks [16]

If your TV has component inputs, you can connect a component video cable to your TV and to your DVD Player for ideal video quality. The component Video Cable only carries the video signal; remember to connect the left and right audio cables. If you connect a TV that is compatible with a Progressive scan signal, you can enjoy both Interlaced and Progressive scan.

2VIDEO OUTPUT S VIDEO jack [16]

If your TV or monitor has an S-video input, clear picture reproduction is possible by connecting the player to your TV or monitor via the S-Video jack.

You can switch between [S1] and [S2] S-video output from the Setup menu.

3VIDEO OUTPUT VIDEO jack [15]

Connect to the video input on a TV or monitor or AV amplifier or receiver with video input capability.

4VIDEO OUTPUT COMPONENT 2 jacks

If your TV has component inputs, you can connect a BNC video cable to your TV and to your DVD Player for ideal video quality.

5RS-232 port

This port is to be used in conjunction with an external controller to control the operation of the DPS-8.3 using an external device.

6AC INLET [20]

Use to connect the power cord to the wall outlet.

7ANALOG OUTPUT CH 1/CH 2 jacks [15-18]

Use to output two-channel audio (analog) to the audio stereo inputs on a TV or stereo amplifier.

8ANALOG OUTPUT FRONT/SURR 1/CENTER/ SUBWOOFER jacks [18]

Use to output 5.1 channel audio (analog) to the 5.1 channel discrete inputs on an amplifier. If you are connecting to a receiver that has both digital and analog input jacks for DVD player connection, it may be beneficial to make both connections.

9SURR 2 jacks [18]

Use when making connections to 7.1 channel analog inputs. (Make sure the SURR 1/1+2 selector switch is set to 1+2.)

0SURR 1/1+2 selector switch [18]

When using 2 channel surround, select 1, when using 4 channel surround, select 1+2. Audio will be output 3dB lower when 1+2 is selected. The same audio is output from SURR 1 and from SURR 2.

-DIGITAL OUTPUT OPTICAL jack [17]

Use to output the digital audio signal recorded on discs. You can output the digital signal via the optical output jack to an AV amplifier or receiver.

=DIGITAL OUTPUT COAXIAL jack [17]

Use to output the digital audio signal recorded on discs. You can output the digital signal via the coaxial output jack to an AV amplifier or receiver.

~IR IN/OUT jacks [19]

If the DPS-8.3 is located inside a rack or cabinet that will not allow infrared beams to reach the IR sensor, you will need to connect a remote sensor to IR IN jack to be able to use the remote controller. Then install the remote sensor in an unblocked location where you can easily point the remote controller.

Using a mini-jack connector, connect IR emitter to the IR OUT jack on the DPS-8.3 and then place the IR emitter on the remote sensor of the component or facing it.

!12V TRIGGER jack

When the DPS-8.3 is turned on, this terminal outputs at 12 V/100 mA.

@z jack [17, 18]

Use to connect this player to another component bearing the z mark. This lets you control this unit as though it were a component in a system.

(The components will not function as a system with only z connections. Be sure to connect the audio connection cables correctly as well).

12