Samsung WS-32Z308T manual Operation, Installing Batteries in the Remote Control

Page 8

Installing Batteries in the Remote Control

1Lift the cover at the back of the remote control upward as shown in the figure.

2 Install two AAA size batteries.

➢ Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment.

3Close the cover as shown in the figure.

➢Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time. The remote control can be used up to about 23 feet

(7m) from the TV. (Assuming typical TV usage, the batteries last for about one year.)

➢ If the remote control doesn’t work! Check the following:

1. Is the TV power on?

2.Are the plus and minus ends of the batteries reversed?

3.Are the batteries drained?

4.Is there a power cut, or is the power cord unplugged?

5. Is there a special fluorescent light or a neon sign nearby?

Operation

Switching Your Television On and Off

The mains lead is attached to the rear of the television.

1Plug the mains lead into an appropriate socket.

➢ The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.

2Press the “” button (On/Off) on the front of the television. The standby indicator on the front of the television lights up.

3Press the POWER button on the remote control to switch the television on. The programme that you were watching last is re-selected automatically.

➢If you have not yet stored any channels, no clear picture appears.

Refer to “Storing Channels Automatically” on page 11 or “Storing Channels Manually” on page 12.

4To switch your television off, press the “” button (On/Off) again.

Placing the Television in Standby Mode

The television can be placed in standby mode, in order to reduce power consumption and wear of the cathode ray tube. Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

1Press the POWER button on the remote control while viewing. The television is in standby mode.

2To switch the television back on, simply press it again.

➢ You can also switch on by pressing the TV (), P /, or numeric button.

☛Do not leave your television in standby mode for long periods of time. Turn your television off by pressing the “” button (On/Off) on the front of the television. It is best to unplug the set from the mains and aerial.

English - 8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Colour Television Page Contents Front of the TV AccessoriesGeneral Information Rear of the TV Side of the TVConnecting to an Aerial or Cable Television Network Connecting to the Component InputConnecting to the Scart Input/Output Connecting to the Hdmi depending on the model@#gh Viewing the Remote Control depending on the modelTeletext Functions Installing Batteries in the Remote Control Switching Your Television On and OffPlacing the Television in Standby Mode If the remote control doesn’t work! Check the followingIf you want to reset this feature Plug & Play Feature depending on the modelViewing an External Signal Source depending on the model HdmiChannel Control Storing Channels AutomaticallyChannel mode Storing Channels ManuallyColour System AUTO/PAL/SECAM/NTSC Sound System B/G, D/K, I, LSkipping Unwanted Channels Sorting the Stored ChannelsFine Tuning Channel Reception Assigning Names to ChannelsAvailable options Dynamic Standard Movie Custom Picture ControlChanging the Picture Standard Available options Cool2 Cool1 Normal Warm1 Warm2 Adjusting the Picture SettingsResetting the Picture Settings to the Factory Defaults Setting the Digital Noise Reduction Selecting the Picture Size depending on the modelUsing the Tilt Control Feature depending on the model Selecting the Film ModeSelecting a Signal Source for PIP Table of PIP SettingsViewing the Picture In Picture PIP depending on the model Activating Picture In PictureSwapping the Contents of the PIP and Main Picture Freezing the Current PictureChanging the Size of the PIP Window Changing the Position of the PIP WindowChanging the Sound Standard Adjusting the Sound Settings depending on the modelSound Control Auto Volume SRS TruSurround XTTurbo Sound Pseudo StereoSelecting the Sound Mode depending on the model StereoSetting the Time Setting and Displaying the Current TimeSetting the Sleep Timer Function DescriptionSwitching the Television On and Off Automatically Absent Power OffSelecting the Melody Setting the Blue ScreenChoosing Your Language Cancel Teletext on/mixSub-page SizePart Appendix Automatic Degaussing to Remove Colour PatchesThis page is intentionally Left blank Correct Disposal of This Product Contact Samsung WORLD-WIDE
Top Page Image Contents