Samsung TXN2771HF/TXN3071WHF Rear Panel Jacks, ∏ VHF/UHF jack, Output jacks, TXN3298HF/TXN3098WHF

Page 11

Y O U R N E W T V

Rear Panel Jacks

Use the rear panel jacks to connect an A/V component that will be connected continuously, such as a VCR or a DVD player.

Because there are two sets of input jacks, you can connect two different A/V components (i.e., a VCR and a DVD, 2 VCRs, etc.)

For more information on connecting equipment, see pages 13 – 22.

Œ AUDIO-VIDEO MONITOR

VHF/UHF jack

OUTPUT jacks

Connect to an antenna or to a cable TV system.

Connect to the audio/video input jacks of a

SUB-WOOFER SPEAKER

recording VCR.

Note: The Monitor Out does not operate in

OUTPUT jack

Component 1 or 2 modes.

(TXN3298HF/TXN3098WHF/

´,¨,ˆAV INPUT jacks

TXN2798HF)

Connect to the Sub-woofer speaker jack (built in

Video and Audio signals from VCRs, DVD players

Sub-woofer cable).

and similar devices.

DVI AUDIO INPUT jacks

Note: The common jack of component 1 and

AV2, component 2 and AV3 input jacks are

(TXN3298HF/TXN3098WHF/

exclusive relation with each other.

TXN2798HF)

ˇ COMPONENT 1 INPUT jacks

Receives the digital audio signals from a set top

box.

(480i/480p/1080i)

˝ DIGITAL INPUT (Digital

Connect to the audio and component output

jacks of a DVD player or Set-Top Box.

Visual Interface) jack

Note: Only black and white signals are output

(TXN3298HF/TXN3098WHF/

from a monitor in DVD/DTV mode.

TXN2798HF)

• TXN2745FP/TXN3245FP: 480i/480p only.

Receives the digital video signals from a set top

Ø COMPONENT 2 INPUT jacks

box.

 

(480i/480p/1080i)

 

Connect to the audio and component output

 

jacks of a DVD player or Set-Top Box.

 

Note: Only black and white signals are output

 

from a monitor in DVD/DTV mode.

 

• TXN2745FP/TXN3245FP: 480i/480p only.

11

Image 11
Contents AA68-02942A-00 Owner’s InstructionsAs an Energy Star Partner Thank You for Choosing Samsung Example Antenna Grounding Page Operation InstallationYour New TV Appendix Special FeaturesTroubleshooting Chapter One List of FeaturesFront Panel Buttons Familiarizing Yourself with The TVSide Panel Jacks Standby indicatorVOL , + Remote Control Sensor ¨ CH and CHOutput jack Rear Panel Jacks∏ VHF/UHF jack Output jacks+100 Remote ControlMode ¨ Number buttons˛ VCR Controls Remote Control ¿ TV/ComponentReset ¸ DNIeAntennas with 300-ohm Flat Twin Leads Connecting VHF and UHF AntennasCable without a Cable Box Connecting Cable TVAntennas with 75-ohm Round Leads Separate VHF and UHF AntennasConnect this cable to a two-way splitter Connecting to a Cable Box that Descrambles All ChannelsConnecting to a Cable Box that Descrambles Some Channels Install AT I O N Unplug the cable or antenna from the back of the TV Connecting a VCRConnecting an S-VHS VCR Make sure the jacks you are using are underneath the numberConnecting a Second VCR to Record from the TV Connecting a DVD Player 480i/480pConnecting to Y,Pb,Pr Connecting a Digital TV Set-Top Box 480p/1080iInstall AT I O N Connecting a Camcorder Installing Batteries in the Remote Control Message Plug & Play is displayed Plug & Play FeaturePress the Power button on the remote control Turning the TV On and OffSelect the Setup menu and press the Enter button If you want to reset this featureViewing the Display Viewing the Menus and On-Screen DisplaysViewing the Menus Selecting a Menu Language Press the Menu button to display the menu Selecting the Video Signal-sourceMemorizing the Channels Storing Channels in Memory Automatic Method Press the Menu button Adding and Erasing Channels Manual MethodChanging Channels Adjusting the VolumeButton to select Channel Labeling the ChannelsOr button repeatedly until the correct hour appears Setting the ClockOption 1 Setting the Clock Manually E R AT I O N E R AT I O N √ button increases it Press the Menu button to exit Customizing the PictureUsing Automatic Picture Settings TXN2798HF/ TXN3098WHF/ TXN3298HF models Customizing the SoundUsing Automatic Sound Settings Viewing an External Signal Source Setting Up Your Remote Control to Operate Your VCR or DVD Customizing Your Remote ControlDVD Codes VCR CodesCodes Setting Up Your Remote Control to Operate Your Cable BoxCable Box Press the button to select Fine tune Fine Tuning ChannelsPress the button to select LNA LNA Low Noise Amplifier TXN2798HF/TXN3098WHF/TXN3298HFPress the button to select Tilt TiltDNIeTM Digital Natural Image engine Press button to select Digital NR Digital Noise ReductionPress the P.SIZE button to change the screen Changing the Screen SizeTXN3271HF/TXM2771HF/TXN3298HF/TXN2798HF/TXN3275HF Changing the Color Tone Freezing the Picture Using the R.Surf FeatureWhen finished, press Menu button Setting the On/Off TimerSetting the Sleep Timer Choosing a Multi-Channel Sound MTS Soundtrack Auto Volume Surround Melody Viewing Closed Captions Activating Picture-in-Picture Viewing Picture-in-Picture TXN2798HF/TXN3098WHF/TXN3298HFTV, AV1, AV2 and AV3 Press the Menu button to exit Selecting a Signal Source External A/V for PIPChanging the Size of the PIP Window Swapping the Contents of the PIP image and Main image Changing the PIP Channel Digits for your PIN and enter them Using the V-Chip USASetting Up Your Personal ID Number PIN How to Set up Restrictions Using the TV guidelines How to Enable/Disable the V-ChipMature audience General audienceParent Guidance TV-14Enter Pin screen will appear. Enter your 4-digit PIN number E C I a L F E AT U R E S Using the V-Chip Canada How to Enable/Disable the V-Chip TV-G Enter Pin screen will appear. Enter your 4-digit PIN number Appear. Enter your 4-digit PIN number How to Set up Restrictions Using the Canadian EnglishEnter Pin screen will appear. Enter your 4-digit PIN number How to Set up Restrictions Using Canadian FrenchProgramming intended for children under age Talk shows, music videos, and variety programming TXN2798HF/TXN3098WHF/TXN3298HF Viewing the DemonstrationChapter Five Identifying ProblemsSpecifications Cleaning and Maintaining Your TVUsing Your TV in Another Country M O